NCS 3.0.1
nrf52840
nrf21540
I have read several tickets regarding antenna diversity and BLE. It does not seem to be supported for BLE. What about Thread?
I have read...
Affected: nRF Connect SDK v3.4.0; the same code is on main as checked on 2026-11-11 ( subsys/net/lib/nrf_cloud/common/src/nrf_cloud_codec_internal.c , subsys/net/lib/nrf_cloud...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Hello everyone,
I am developing ble data transfer from some custom EMG sensor for decoupling purpose. The desired ADC sampling is very fast (200us) and sampled data should...
Hi,
We tried to build firmware sample ubx_bmd345eval_nrf52840 to ublox bmd-345 with the template nrf/samples/openthread/coprocessor unsuccessfully.
Added the next lines...
What is the default factory firmware when nRF52810 chips are produced and delivered as new electronic parts? Before assembling and programming them for a particular product...
When using MSEC_TO_UNITS for min and max connectivity interval, the documentation says MSEC_TO_UNITS can take in parameter value for time between 6 to 3200,
but when I am...
Hi,
after working with old SDK on nRF52 for a long time, we decided to switch to nRF53 with the new SDK and toolchain for our new project.
When I tried installing the...
i'm trying to change nrf/samples/bluetooth/throghput to coded PHY advertising.
I changed the scan options to BT_LE_SCAN_OPT_FILTER_DUPLICATE | BT_LE_SCAN_OPT_CODED | BT_LE_SCAN_OPT_NO_1M...
Hello,
I am setting up a new workstation but when trying to build code that was working on another computer I am getting the following error
I am trying to use cpp...
Dear Nordic Team,
I am trying to send numbers in Cjson format through MQTT. However, I am getting errors as shown in the diagram below. I have attached my code below. May...
I use the nRF52-DK with nRF Connect SDK 2.2.0 with the peripheral_uart example.
The aim is to use the filter_accept_list to allow only bonded devices to connect to the peripheral...
Our product uses the BMD-360 which uses your nrf52811. We are trying to add a feature that would allow us to update the chip from our controller, but it seems the file is...
Hi, I have a bluetooth central app which connects to several BLE peripherals and am now working on fixing various connection reliability issues. White lists and bonding are...
Hello,
SDK: 15.0.0
We already have a working bootloader using the default adv name setted in sdk_config.h. But we want to add to the DFU advertising the serial number...
I have for some while had a project running in which NRF52840 operates in SPI slave mode. Using "modules\hal\nordic\nrfx\drivers\src\nrfx_spis.c"
Lately i have been stressing...
Software engineer here and very new to electronics. I programmed a nrf52840 dongle that activates a signal with a transistor. Now, I'd like to hide it inside the wall but...
Hi everyone
I am testing the modbus library over zephyr framework (Nrfconnect (skd v2.2.0 ) on visual studio code).
I started from the examples ( link ) and I am implementing...
