Using nRF Connect SDK v3.4.1 with an nRF9151.
CONFIG_NRF_CLOUD_AGNSS currently has unconditional dependencies on:
depends on MODEM_INFO
depends on MODEM_INFO_ADD_NETWORK...
Hi
I am working with nRF Cloud - using a developer account (limited to 10 devices).
After connecting a few times with a device (using a different serial each time),...
I was wondering if the nPM-FG schematic or board design is available, I'm interested in using it to profile a few CR123A's.
The docs suggest the firmware/schematic/layout...
Hi,
On nRF Connect SDK 2.7.0 ( sdk-nrf v2.7.0 , Zephyr v3.6.99-100befc70c74 ), enabling the non-minimal TF-M profile causes WPA2-PSK association to fail during the 4-way...
Hello,
The nrf9160 took over 3 minutes to connect to a cell tower after moving from one country (Singapore, NBIOT) to another (Canada, LTE-M).
After moving, the nrf9160...
Hi Nordic team,
I am testing Channel Sounding on the nRF54L15 using the ras_initiator and ras_reflector samples, and I am seeing a significant difference between measurements...
Hello,
First let me say I'm new to Nordic tools and SDK. I have been lurking on this forum for a while and it has helped solve a lot of my issues in the past. I couldn't...
Hello
I tried to follow the instructions to install the nRF SDK Connect and I found the following issues:
There are 2 sets of instructions :
option 1 :
https://nrfconnect...
Hi! We would like to build two different sw variants from same source code and mostly the same config options, probably only needing a single "define"-difference in code....
Hi,
We have a question regarding firmware over the air update, can we update the firmware of the devices connected in Mesh network or we need to connect single device...
Hello,
to use the twi sensor library should I define for each sensor an own NRF_TWI_SENSOR_DEF?
I found not really a documentation about the usage of the twi sensor library...
Hi,
I've got a lot of BLE_GAP_EVT_TIMEOUT when my ble central trying to connect with BLE peripheral (sometimes more than six in a row).
The configuration of my system...
HI,
I have couple of questions here.
1.Is there any sample application that upgrade firmware over BLE using zephyr/NCS 2.1.0 for nRF52840
2.If so our requirement is...
We are using QSPI XIP mode to access data in external flash for our project. We are trying put QSPI peripheral in standby mode.
However, we can't uninitialized QSPI peripheral...
I want to develop a device with the following selection.
BLE module: Raytac MDBT42V (nRF52832)
nRF Connect SDK v1.2.0
Where can I check the version of SoftDevice...
Good Day!
I have a Samsung Note 10 smartphone (it supports Long Range) and I want to connect it to an nRF52840 microcontroller using BLE Long Range.
What is the approximate...
Hello
I was using the NRF52840 dev kit as J-link to develop a custom board. at first was working, i uploaded a blink code to it then i modified the libry from gpio.h to...
Hi,
We used the SLM (serial LTE modem) application in our custom board with NRF9160 configured as a slave chip and interfaced with an STM32 MCU via UART interface. The SDK...
Hi there,
Currently developing a producting using two nRF52833 boards one as peripheral and one as central:
- 125kbs coded phy (S8)
- 40 byte MTU
- using extended...
Dear Nordic Engineers
I have a question, it about SPI PIN input voltage of NRF5340.
Our cutsomer use NRF5340 and STM32 develop a product. STM32 and NRF5340 use SPI to...
Hi, we will shortly be sending our product to an independent lab for testing. They have asked us to provide any available documentation/certificates that apply to the on-chip...
