Running a test that sends a small ping packet to a server about 1/minute and I'm seeing intermittent board resets. I'm still trying to track down the cause, but in one case...
Hello Nordic support,
We are designing a battery-powered device using the u-blox NORA-B206-00B module, based on the nRF54L15. u-blox support recommended contacting you regarding...
Hi Nordic DevZone,
We are currently looking at how best to handle nRF9151 programming in mass production, and I would like to understand Nordic’s intended approach a bit...
Hello, The nRF9151 hardware design guidelines (power sequence) require VDD_GPIO to be applied at least 6 ms after VDD and ENABLE, after the hardware boot. In our design a...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
Hello,
I'm currently trying to convert the SPI example project for NRF52811 for the EVK BMD-360 and ran into an issue.
I'm using segger embedded studio 5.42a and nrf sdk...
Hello Nordic Dev Zone,
I have been developing on the nrf5340pdk and recently switched to the nrf5340dk.
I utilized the COM console output for app/net cores via the `minicom...
Good day,
I have successfully implemented exercise steps 1 to 5 of Exercise 2, Lesson 3 of the DevAcademy "nRF Connect SDK fundamentals" course, that deal with "adding custom...
Hi,
As i2c communication + computation takes 45ms in my timer interrupt that happen each 100ms and gave issue with SD, I decided to set a flag in the interrupt and execute...
Is there a configuration / sample available of mqtt simple to talk to the mosquitto server using an authenticated client on port 8884? I saw a message on here that was about...
Hi,
I want to get the GPS value from A- GPS continuously.
Meanwhile, if there is any new application firmware version update,
I would like to download the image with...
I see the problem here. use the dfu-util command in the window system
and i tried many methods and failed The following is my reference website
http://zadig.akeo.ie...
I've been playing around with some code that puts my hardware into System OFF mode to save power, and then will exit this mode and start up when one of three different GPIO...
Hi,
https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink
I have tried the example you modified. It works fine. However, I get ERROR 17 NRF_BUSY when 2-3...
Excited to have ordered my BLE Audio DK which uses NRF5340.
In my use case I am looking for many microphones (audio transmitters) to a single listening device (audio receiver...
Hello!
I am working on a medical device project utilizing nrf52832 microcontroller. We use a mobile app to control and interact with the device through BLE since the device...
Basic Bluetooth connection question
How do advertisements usually work? So I have earbuds and a phone. When I pull the earbuds out of the case they auto connect to a bonded...
Hi All!
I am using nrf52820/33 and am able to successfully connectable advertise (coded PHY) by nrf5 SDK. Now I want to use NCS (Zephyr RTOS) to do the same job . Can...
Hi! I'm trying to use the nRF Connect App on a M1 Mac. I keep getting the error shown above with my Jlink connected.
This is the output of the nrfjprog cli tool:
How can...
Hello,
I have been experimenting with the direction_finding_peripheral sample in the nRF Connect SDK. I have been trying to connect to the peripheral using a custom device...