Hi,
I am currently testing the dect_shell example on two nRF9151 DKs and achieved a range of ~500m. I want to transition this setup into a multi-hop mesh network topology...
Hi: The device shows successful reconnection, but the mobile end is not connected.
And the connection information displayed on the device is (public), which is actually...
I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
For the nRF54L15, what is the voltage at the output pin of DCC (and input pins of DECD, DECA, and DECRF) in DC-DC mode?
Is it 0.9V? Is it constant?
Vinson
Hi,
We are using both nRF54L15 and nRF54L10 in our product, with DFU support where an external flash is used as the secondary partition on both MCUs. The hardware connections...
Dear Sir,
I am getting the below Error During building of LED Blink Program for nRF52840 Module using PCA10056. Below code I am Trying to run:
#include <stdbool.h> #include...
I am using the PPKII to supply a 1.8V supply for a circuit board in my measurement setup.
I have been battling a low-frequency oscillation at 0.5Hz at around 5mVpp, which...
Hello!
I want to make a self-test that verifies the speeds of the 32.768 kHz clock and the 32 MHz clock.
The idea is that if the ratio (976.56 to 1) is correct, then the...
I have started working with the nFR9151-DK board. After some time, I may have accidentally erased all data from the board using the PROGRAMMER application. As a result, the...
hi Nordic
i am working with nrf52840 and nrf52832 with ncs v2.8.0
i am also working on nrf54l15 (since nrf54h20 seems to not be fully integrated yet)
i want to know...
Hi,
I am trying to do t rilateration using one initiator and 3 reflectors. For now I am just trying to get 2 reflectors to work.
Sadly I cannot get the initiator to...
hi support team,
may i ask how to test 54l15+21540 dtm? i have send code to customer, but they feedback to me that the output power is 15db, not 20db(using serial send command...
Hello,
The customer, T&D would like to registrate their product to Bluetooth SIG.
Then, design number shoule be required, however, regarding SDK3.0.2, there isn't any...
I am working on an nRF54L15 project and started from: C:\ncs\v3.0.2\nrf\samples\bluetooth\peripheral_uart as the base. I would like to trigger an interrupt once every second...
In the reference schematic design of the 54L, why does the RF circuit use three LC circuits? What is the purpose? This approach would likely result in higher insertion loss...
I have made a PCB using a BL5340PA module, to start i have tried a simple code to see log from RTT using the SWD SWCLK pin, i am using an NRF5340 DK as debugger/programmer...
Hi apparently the examples are not working out of the box. I do not see any documentaiton on what has to be done for them to work. Can you advise me on what i shoud do to...
