Hello,
I have 2 Memfault projects that I'd like to rename, but I can't find any way to do this through the web app, and the API authorization keeps getting rejected (tried...
Hello, I'm working on a prototype device based on the nRF9151 DK.
HW: nRF9151 DK, nRF9151 LACA A1A Tested with modem_shell sample app, NCS v3.4.0.
Symptom: on boot, "The...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
Hi
Is there an example for BLE "Just Works" using the NRF Connect SDK for the peripheral device?
I am using a peripheral device without display and would like to allow...
Hi,
In our application we use a motor. In the case that the watchdog would trigger while the motor is running, we need to stop the motor. For this we need to set the PWM...
Hi, all,
At first, I have to say I am a newbie in programming for BLE. ^^"
I trying to development a cycling power meter, so I want to modify this CSCS example to...
Hello, Recently I tested and flashed the Zephyr program to the nrf52840DK, it works fine. While I flashed as usual last time, I saw the LED5 flashing and then the PC didn...
I would like to perform a OTA DFU in a nRF52840 DK using nrfutil. For that, I'm using the example that is in SDK/examples/dfu/secure_bootloader/pca10056_s140_ble in the target...
Hi
I have follows the following steps.
1) I build 'hci_uart' sample for nRF5340DK successfully by following guide https://docs.zephyrproject.org/latest/samples/bluetooth...
Hi, I tried the fourth step of this guide https://openthread.io/codelabs/openthread-hardware#3 , but if I start the OpenThread daemon, I got this output that is not the same...
Hi There, I'm trying to read the NDEF records stored on my NRF52 DK but I'm having some issues when the the NDEF record payload is less than 4 chars. I just get random symbols...
Hello,
I've recently run into an issue with the Command Line Tools. I was using version 10.13.0 up until today, and everything was working fine. When I updated to 10.14...
Здравствуйте, я использую Honor 8x телефон. Я считаю, что это очень трудно использовать приложение на этом телефоне. Соединение происходит только один раз, и после одного...
as i said above,i got 1.5GHz radio signal,such as follow:
left is 1.5G,right is 2.4G
I want to know if the PA is configured correctly in my code.
here is my code:...
Hi,
What is the best starting point(Sample) for project with:
OS (like FreeRTOS)
BLE data advertisement.
I already install nRF connect SDK 1.7.0
Thanks
We have our one of Product Firmware of NRF52832 written in the Keilv5. As the Application use the Softdevice Functionality we need to load Softdevice code and Application...
Hi,
I'm using Windows 10, Python 3.10, Wireshark 3.4.9, pyserial 3.5.
Hex used : sniffer_nrf52dk_nrf52832_4.0.0.hex
I see this question has been asked before but the...
