Hi
I am working with nRF Cloud - using a developer account (limited to 10 devices).
After connecting a few times with a device (using a different serial each time),...
I was wondering if the nPM-FG schematic or board design is available, I'm interested in using it to profile a few CR123A's.
The docs suggest the firmware/schematic/layout...
Hi,
On nRF Connect SDK 2.7.0 ( sdk-nrf v2.7.0 , Zephyr v3.6.99-100befc70c74 ), enabling the non-minimal TF-M profile causes WPA2-PSK association to fail during the 4-way...
Hello,
The nrf9160 took over 3 minutes to connect to a cell tower after moving from one country (Singapore, NBIOT) to another (Canada, LTE-M).
After moving, the nrf9160...
Hi Nordic team,
I am testing Channel Sounding on the nRF54L15 using the ras_initiator and ras_reflector samples, and I am seeing a significant difference between measurements...
Hello all,
I am looking to hire a developer experienced with ANT+ together with BLE and the nRF52840 SoC, possibly the nrf54L10.
I am looking for the coding for the...
nrf9160 modem Firmware version 1.3.0 release listed nidd or non-ip support. in the firmware.
We are eager to use this feature to send/receive data over RF control plane...
"CTE can be used in both connectionless and connection-oriented scenarios. For connectionless use, the periodic advertising feature is required (since deterministic timing...
Hello all,
I'm using NRF52840 with last sdk (V1.6.0) of nrf connect but I can't put the device into sleep mode (where the current consumption is at about 3/4 U) the device...
Hi,
I need a 1Hz clock with its interrupt function.
Where do I find an example to set the timer RTC0 or RTC1 to 1Hz and how to set the timer callback function?
Thanks...
Hi,
I am using nrfx_twim driver, and I want to read value from sensor's register. When I want to do that sequence looks something like this:
(SENSOR_I2c_ADDR+Read_bit...
Hello Sirs
I have two questions about the nrf5340-dk evaluation board.
The first one is how can I get the scan data of an advertising device?
And the second is that...
Hi,
My dev environment is as follows:
nrf52840 + s140 +SD7.0.1 + SDK17.0.0.9 + SES + nrfutil v6.1.0
I started my development for DFU and utilized secure buttonless DFU...
Hi there,
Currently, I am getting an error with a low power node when the remote cannot configure through another regular node in a mesh network. What causes me to get this...
Hello Nordic support,
I would like to use the APIs in IEEE 802.15.4, especially mlme_scan_req in nRF5 SDK for Thread & Zigbee for a ZigBee application in order to scan for...
I want to use the Nordic UART/Serial Port Emulation over BLE to communicate to a windows or linux host computer.
I see Andriod and IOS haveapps available to support Nordic...
Hello,
I have upgraded my project from nRF_Connect 1.5.1 to nRF_Connect 1.6.0.
It runs on nRF9160 and I use RTT viewer v7.50a.
The problem that I see is that the logs...
Hi everyone,
To give a first introduction, I have been working with this development kit for a while now. I'm trying to develop a Zigbee device and I'm very close to finishing...
Hi,
I want to scan for broadcast messages from a specific device that I never connect to (not bonded to for sure) and I want to filter out messages from other devices! to...
Hello,
In my project i want to interface M24C16-R external flash using i2c
I am using SDK 17.0.2 and nrf25832DK
So, the problem is first i have used "twi_scanner"...
Hi,
We are working with nRF Connect SDK v1.5.1 and an nRF5340 device. We want to use the hci_rpmsg sample from the SDK to run in the net core, but we want to move the directory...
