I've updated the nrfconnect sdk to the version 3.0.1. and the zap tool version is 2025.5.22. The sdk supports matter 1.4, but the new device type of mounted dimmable load...
Hi, I'm working on enabling **FOTA for the application core only** on **nRF5340**, based on the **`nrf5340_audio` example**, using **only internal flash** (no external flash...
Hello,
I have a Thingy91x and I'm having problems using the samples: "Cellular: GNSS" ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/cellular/gnss/README...
Hello Nordic,
We have recently purchased an nRF52840 Dongle. We were able to sniff the BLE packets over the air. So it is found that all the packets that we are able to...
We are currently using an nRF53 in our plant sensor project, where we need to be able to enter sleep mode and be woken up via RTC and GPIO interrupt. Since the nRF53 does...
Hello,
I am currently using the nrfutil application to convert modem trace logs to pcaps through an automated process. I am seeing intermittent failures with the following...
Hi there,
I am in the process of developing a custom PCB using the nRF52833 SoC. This board is quite simple, and doesn't use many of the pins of the nRF52833 SoC.
I am...
nRF5_SDK_16.0.0_98a08e2\examples\peripheral\uart. In the SDK 16 ,UART example,why the legacy driver nrf_drv_uart.c is used instead of the sdk recommended nrfx_uart.c.
Secondly...
hello,
I'm using SDK 16.0 with nrf52832, for storing some information iam using flash storage, during initialization, we are giving a starting and ending address to flash...
Hi friend,
We have a project with BLE connection. It sends out the Manchester data and the data modulates with 125KHz. Can we use PWM to do that? Will the data format be...
My platform is SDK16 with softdevice, MCU nRF52840. I used 2 pin to generate PWM at 125KHz for Manchester coding. I want them are at different pin polarity. For example, if...
Hi all,
I am working with the nRF52 dev kit and the ecg sensor MAX30003. Using MBED to develop firmware.
I am using this library and the example code from maxim ( https...
Hello,
I need to develop an application for nRF51822 that uses SoftDevice 110 v8.0.0 using SDK 12.3 and extend it to use buttonless DFU for the legacy DFU bootloader of...
Hi, support team
I need to realize two-wire uarte receiver(with low power), in the scenario there is no data come from TX in most time, so after receiving the data I need...
SDK: 15.3.0
BOARD: custom nRF52840 pre-product
Hi, I want to implement usb dfu trigger library.
but, faced with a problem.
My project are started from usb cli...
cli_agent_router and multi_sensor example with nRF5_SDK_for_Thread_and_Zigbee_v4.1.0 nrf52840
problem: The coordinator restarts occasionally, and the zed cannot rejoin until...
Hello,
I am trying to configure the SAADC for the NRF52810. I read that I have to enable it via the sdk_config.h. Here I find an entry for:
NRFX_SAADC_ENABLED - nrfx_saadc...
I have two related questions about nRF52 (nrf52832) which I have not been able to pinpoint from the documentation.
Can the 32MHz crystal connection be replaced by...
Hi. I’ve developed a custom device based on nRF9160 and now have a problem of fixing GPS signal. With the same antenna and same conditions sometimes it takes up to 10 minutes...
I've set up a timer which is firing the interrupt correctly. I then set up a second compare and linked it to the PPI to fire the ADC. The idea is to do these a few times per...
