Hi
AFAIK CRA needs SPDX 3.0 which can no be generated by west ncs-sbom in NCS 3.4. Will SPDX 3.0 generation be backported from 3.4.99/3.5 to 3.4 LTS?
Thanks in advanc...
Hello Nordic support,
We are designing a battery-powered device using the u-blox NORA-B206-00B module, based on the nRF54L15. u-blox support recommended contacting you regarding...
Hi Nordic DevZone,
We are currently looking at how best to handle nRF9151 programming in mass production, and I would like to understand Nordic’s intended approach a bit...
Hello, The nRF9151 hardware design guidelines (power sequence) require VDD_GPIO to be applied at least 6 ms after VDD and ENABLE, after the hardware boot. In our design a...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
Hi,
I am trying to implement application timer to ant+ examples in SDK15.2. I used application timer tutorial here on devzone. The project builds fine, but when i run it...
So the nrf53 codebase is pretty much non-existent from what I can see. Is there any example code to launch the proprietary Enhanced Shockburst in receive mode?
Kind of like...
Hi, I've got an application where I need to send a message and then receive a response on a half duplex serial link.
I feel like this is a pretty common use case but the...
Has anyone added cpputest ( https://cpputest.github.io/ ) to Segger Embedded Studio and can share the setup? Can build with some minor changes (had to disable CPPUTEST_USE_STD_CPP_LIB...
Hi,
I'm trying to integrate the light switch server example in nRF5 SDK for Mesh v4 with ble app beacon from the nRF5 SDK v16. I added the advertising_init and the advertising_start...
hello again,
i spent the last three days on the theme dfu, bl, app, sd. Now there are some questions I can't answer me with reading.
Question 1) Does a new app works ...
Hello!
In our design we need BLE 5 solution with maximum allowable by reulation +20 dBm TX power. It is not a problem to use a separate PA for achieving that power, however...
Unable to obtain repeatable scan response data.
I can obtain advertising data and scan response data from 3rd party devices. I can obtain advertising data from my server...
When initializing models from the models_init_cb it's useful to check the current configuration using the mesh config API. However, the returned values are always the default...
We are testing GPS capabilities for our hardware, using mfw 1.1.0 in the field. We have the following test conditions
The unit is ackquiring position every 5 min
the...
Hello,
We are trying to run the ble_ant_app_hrm example on nRF52840DK using nRF5_SDK_16.0.0_98a08e2 SDK and ANT_s340_nrf52840_6.1.1 softdevices (both latest as of today...
Hi,
I was looking for information about the MLME-ASSOCIATE primitives in the https://infocenter.nordicsemi.com/ . The section with the "MAC MLME Association API" title...
Hello. After I updated the firmware on Thingy 91, it no longer registers on the network via LTE - the LTE indicator in LTE monitor blinks between yellow and red, and I get...
Hello Nordic team,
I was wondering how to determine the QDID of our product. The relevant QDIDs are 101625 and 97989. I believe the latter should suffice but I am not sure...
Sir After Flash the code to board i am getting some info message in teraterm
below i have attached the image of the teraterm
Refereed link: https://infocenter.nordicsemi...