Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
Hi!
Does latest NRFUTIL 4.0.0 include mesh update option?
I saw in branch dfu_mesh on pc-nrfutil github that this branch was last updated on 16.12.2016 (nrfutil 0.3) and...
In my project LPN node need to communicate with more than one friend node.
Is it possible to make multiple friend establishments by single LPN node or is it something like...
Hi all,
I started a project on nRF52840 dongle with Segger IDE. I used SDK15.2 given by Nordic and my goal is to develop a program that permits to communicate between...
Hi,
Noted that nRF mesh app needs GATT bearer to provision a mesh device. I'm using 2 nRF52 DK boards, provisioning is fine, set the keys, subscription lists, etc, everything...
Hello, First of, I'm developing with eclipse an application based on the freertos example of the SDK 15.0 with softdevice S132 v6.0.0. My problem is that the nRF52 sometimes...
Hi. I have the latest topology monitor downloaded from the home page. It seems to have a problem. Every time i try to run it from my windows 10 machine (32 bit), it gives...
nRF TTM win32-x64 will not run on my PC. I use Windows 10 and am trying to run the executable but i keep getting "app cannot run on your PC. Contact the publisher....".
...
Hi. I managed to set up a mesh (Thread) using 9 nodes of the nRF52840 SoCs. I am currently using Putty to send commands and pings between the nodes. What i need now is a way...
Hello, another question from me :) First of all, I'm working with Eclipse, GCC compiler and SDK 15.2.0. I want to add GPIOTE funtionality to the TWI example of Nordic. I'm...
Hello there,
I've been struggling to find a way to read IMU values from my custom PCB. This PCB sends a notification as shown in this image:
My main objective is implementing...
Dear nordic,
i want to BLE+FDS application i have some doubts regarding this.52810 has only 192kb flash if i use both BLE application and FDS is it any problem occurs? ...
Hi,
We used nrf52832 in our custom pcb. It works.
NRF52840 has "Long Range" feature. We think, if long range needs in some application, we can set 8dBm output power and...
Hi,
I am using nRF5_SDK_12.3.0 and writing customized firmware based on uart example.
Everything works fine with the DK. Then I program the firmware to a nrf51822 module...
I have a DFU issue; SDK nRF5_SDK_13.0.0_04a0bfd
The system reboots on the DFUTAG after having completed the application upload.
I have the following errors : :DEBUG:Error...
