nRF Cloud — CoAP transport (device shadow) Date of incident: 2026-06-22, ~13:04 UTC — still unresolved at 20:42 UTC (7h38m+) Device: nRF9151, modem firmware mfw_nrf91x1_2...
We are doing a DFU over BLE with the second MCUboot partition on an external flash. Some times Zephyr can't access the flash after booting, resulting in a bricked device,...
Hey, I am trying to implement ecdh key agreement and derivation, but I am getting PSA_ERROR_INVALID_ARGUMENT (-135) from psa_key_derivation_key_agreement: Any idea what is...
Hi,
I have a question regarding the SAADC timing parameters.
I could not find an official specification for the SAADC power-up time (t_PWRUP). While measuring it on my...
I am using nRF54L10 with nRF Connect SDK v3.1. The device connects over BLE, wakes every 30 minutes to read sensor data, and then should enter deep sleep (System OFF). However...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
The following log is a compilation error.Is there any way to correctly compile?
e:/nordic/ncs/toolchains/fd21892d0f/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr...
We have an application where response time is critical, and we are trying to minimize the time from advertising to an active channel sounding session.
What we have already...
Dear Nordic,
We are currently evaluating the Amarisoft CallBox as an end-of-line (EoL) testing tool.
In an ideal scenario, we would like to use 1NCE production SIM cards...
When performing FOTA using NCS 2.9.2, we observed that the swap using move process takes approximately tens of seconds. However, with NCS 3.2.4, the same swap using move operation...
nRF Connect SDK v3.2.3, nRF9160.
Hi,
I'm working on a project which has MCUBoot enabled (dual slot) for firmware updates over cellular connection. I did not have a pm_static...
Hello,
I want to program the bare nRF52832 MCU over SWDIO, SWCLK, GND and +3,3V Connections with a Segger J-Link programmer. Unfortunately the programmer could not connect...
Is it possible to be able to get hold of some of the legacy software for the nRF52 BLE sniffer that works off the old nRF Command Line Tool rather than the nRFutil? As I'm...
Hello together!
I am trying to reproduce the ultra low power connection as described in this whitepaper: /cfs-file/__key/communityserver-discussions-components-files/4/3482...
Ultrasonic welding is commonly used to seal plastic enclosures for electronic devices. 32kHz crystals can be damaged by this type of welding and manufacturers recommend not...
Does APPROTECT supersede SECUREAPPROTECT or do both need to be enabled for maximum security?
Similarly, do the HW protections (APPROTECT, SECUREAPPROTECT, ERASEPROTECT)...
I am trying to measure current on a nRF52 DK v3.0.0 using PPK II in source mode.
I cut SB9 and soldered SB12 as described in this guide: https://docs.nordicsemi.com/bundle...
Hello , I 'm trying to use the Lan865x (two -wire eth click ) chip with the nrf52840dk board , using zephyr 3 . 7 . I 'm getting always this error while trying a net sample...
Hello!
I've been trying some of the solutions around these forums but I can't seem to get my nRF52840 DK to show up on my device manager so I'm unable to flash anything...
NCS 2.7.0, NRF52840, SYSBUILD with MCUBOOT
We have 1 specific board which is failing with a hardfault and assert MPSL ASSERT: 112, 1617 it occurs whenever we activate...
