With PM device runtime enabled ( CONFIG_PM_DEVICE_RUNTIME =y ), calling uart_irq_tx_disable (actual driver function uarte_nrfx_irq_tx_disable) may result in increase the PM...
We feed the nRF54LM20A’s VBUS pin (the USB high-speed PHY) from the nPM1300’s VBUSOUT, so that the PMIC’s input protection guards the module and the processor sees VBUS only...
Hello,
I am experiencing an issue with my nRF52 DK. The target nRF52832 appears to be working, but the on-board debugger is not functioning.
Symptoms:
No power/debug...
I have two nRF9151 DKs and want to evaluate direct, SIM-free DECT NR+ communication using FT and PT roles. Please help me with:
- DECT NR+ MAC/PHY modem firmware, rather...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
Hello,
Recently we're planning to start our nRF-9151 custom board production.
I've designed my own PC program to confirm all the connectors out application used are doing...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Hello
I was working on a project, trying to enable the power management but I could not. So I just tested the simple zephyr sample application device_pm just to see if there...
Hello. We are testing the example of bl provisioning provided by sdk v2.8.0.
When the first wifi is connected, the wifi's data is stored on the board, and even if you turn...
Hello Nordic Team, I am working on a LE Audio project on NCS v2.9.0. My development board is nrf5340-dk. I am using unicast client example and I am trying to use it with my...
Hello, I have recently switched to nrf52840 dongle for 802.15.4 sniffing.
I did a simple test with a ZigBee Green Power sensor sending data on channel 11. On the receiver...
Hi,
I am using a nrf52840 dongle for sniffing the bluetooth connection between 2 devices. These are the wireshark logs
What I could see is it initiates the pairing with...
I have a custom board with a nrf9160 on it that has been working for the last three months but last week when i was evaluating low power modes on the board i couldn't talk...
Hi,
i am using SDK version 2.1.1 and recently we had a problem due to the errata 160 which is fixed also in SDK 2.1.4
I am using Toolchain Manager 1.5.3 and i cannot select...
Hi,
we plan to use the nRF52832 in a new project, where we will need ANT support.
I've seen that it is possible to use the nRF5 SDK and the SoftDevice 332 to have ANT...
Hi everyone, I have a problems when I build custom board NRF54L15. I build this project for custom board for nrf52833. It's okay and no error. After that, I change this board...
I have issue in newest SDK 2.8 of nRF Connect for VS Code. When I change something in prj.conf or in the source code, I often have to build and compile two or more times to...
I have looked at forum_post_1 , forum_link_2 and forum_link_3 . In short, I am following instructions for my_dongle . I have ncs 2.6.1. I have clones of nordics git repos...
I notice in github.com/.../nrf802154_sniffer.py that there is a line saying: TODO: Add toolbar with channel selector . I know extcap supports these toolbar controls and a...
Hi
At nPM1300 product specification V1.1 page 148(8.1 Schematic)
The control I/F between nPM1300 and nRF5x is TWI(I2C), and there is four signals(SCL, SDA, Reset, INT...
