I have an application which is not able to talk with my gas gauge device when the TI EV2400 can. Looking at the waveforms all look the same except for the Zephyr code has...
Is there a recommended way to access the USB data lines from the J3 connector of the nPM1300EK? I would like to be able to charge the battery and also provide a USB mass storage...
Hello,
I am currently testing DECT NR+ communication between multiple nRF9151 SMA DK boards, but I am unable to establish a connection between an FT and a PT.
I initially...
The nRF91 series of modem firmware are distributed with FOTA-TEST diffs to allow for validation of FOTA integrations. Will the nRF93M1 firmware images be distributed with...
Hi Nordic team,
I am using the nRF52840 HCI USB project as the controller firmware, with a Linux device acting as the Bluetooth host.
My application has multiple BLE connections...
Hello DevZone Community,
I wanted to share a unique hardware-in-the-loop implementation using the Power Profiler Kit II (PPK2). While the industry is heavily focused on...
Hi,
I am developing on the nRF5340 and using an external modem and an external GNSS module. I am using SDK version 3.4.0.
To operate the modem, I use `modem_cellular...
Some of the products we produce do not work after about 10 days. Our firmware starts the watchdog module as soon as it starts, and sets the timeout period to 30s. And read...
I would like to implement ANALOG Modulation schemas on nrf52 serias family (e.g. AM, FM, SSB)
Do I have a direct access to IQ samples OR basic properties of the radio carrier...
I am using is25lp03d flash with "nordic,qspi-nor" driver.
The issue is that nrf_qspi_nor.c driver uses `nrfx_qspi_mem_busy_check()` before entering suspend mode. This function...
The %XCONNSTAT read command returns the total amount of data received/transmitted "in kilobytes". By kilobytes, does the documentation mean 1000 bytes or 1024 bytes?
Hi
I would like to have a project using 52840 witth softdevice 17, and I need to use internal flash to make a USB mass storage device
I reference to ....\examples...
Hi,
I need to create partition of size 4kb but using psa_ps_set() I could not able create partition of size more than 1Kb, If I try to create 4 kb Partition it's throwing...
Hello,
Creating a simple project in nrf connect 2.6.1 I start with looking at power consumption.
I need upgrade over USB, so I have added this to .prj:
In the...
software: ncs 2.5.0, zephyr\samples\drivers\counter\alarm
hardware: nRF52840dk
Step1: main.c is not be r evised!!!
Step2: prj.conf like this:
Step3: overlay file...
Hi Nordic Team,
I am currently working on a project that involves two devices, both using the nRF52840 microcontroller.
Current Setup:
Device A : I have successfully...
hello Nordic
we are working with ncs v2.5.0 trying to migrate to 2.7.0
1. so that there is several rcs, should i take v2.7.0-rc3 or v2.7.0 ?
2. while choosing v2.7.0...
Hi all,
I wonder if nrf9160 has a built-in temperature sensor interfaced with the ADC, that could help to diagnose the internal chip temperature?
Thanks.
I would like to use the Power Profiler app (with PPK II) as a pure coulomb counter for accurate long term (> many days) cumulative device energy consumption without saving...
Hi there,
We have a product running on nRF5340 with an existing workaround that was carried over from an nRF52840-based product, where SAADC readings are prevented from...
Hi Nordic Team, I'm currently working with the nRF5340 Audio DK to broadcast multiple streams, where the receiver can select which stream to listen to. To the reciever, this...
I have an ILI9340 connected to an nRF53 and want to use LVGL in Zephyr (NCS 2.6.1), but I got no label, etc. showing up. Instead, the display is showing a white screen.
...
