Hi
in conn_time_sync some thing must be broken. Central and peripheral connect to each other. The logs look as expected.
BUT:
THE LED's wont blink.
When I copy a sample...
My device uses the nRF52840. I migrated my Zigbee application from nRF Connect SDK v2.5.1 to the Zigbee R23 add-on v1.4.0.
After migrating to the R23 add-on, I noticed that...
Hello Nordic Semiconductor Support,
I would like to request an RMA/replacement for an nRF52840 DK (PCA10056) that appears to have a failure in the Interface MCU/USB debugger...
Hello, We have a question about the errata workarounds applied in SystemInit() in nRF5 SDK v16.0.0. Our firmware is split into two images: a boot application and a main application...
Hi, I am experiencing an issue where a specific nRF9151 SMA DK kit is stuck in an infinite network registration loop. The modem continuously reports +CEREG: 2 (Not registered...
Hi
I am planning to develop a product based on the nRF5340 DK.
Please provide a response to the following inquiries:
1. Is it possible to obtain the schematic and PCB...
Hi Nordic,
We have a reproducible bus fault in nrf_modem_dect_phy_tx_harq() on nRF9151 that we believe originates in the modem library rather than in our application, and...
Hi,
I've got two ESB transceivers talking to each other - a PTX on nRF52832 (E73 module) and a PRX on nRF52810 (Holyiot module, the "tag"). Both chips can obviously TX and...
NCS-3.4.0, on nRF5340, custom board losely based on PAN1783. No RTT backend, BLE stack works properly:
RTT enabled, BLE stack reads some garbage:
Printing is done...
Hello,
I have a pin on port 1 of the nrf54l15 that I am bitbanging for a custom tx/rx 2-wire protocol. I have already managed to implement the tx capability and I was hoping...
Can I copy the ESB code from SDK v3.3.0-preview3 into SDK v2.9.0, and then get the functionality in esb_ptx_ble & esb_prx_ble?
Is there any way to achieve it quickly?
Hi
in conn_time_sync some thing must be broken. Central and peripheral connect to each other. The logs look as expected.
BUT:
THE LED's wont blink.
When I copy a sample...
Summary
On a small fleet of identical nRF52832 units running the same firmware (NCS 2.5.1, SoftDevice Controller, BLE peripheral, LFCLK = RC with calibration), individual...
My device uses the nRF52840. I migrated my Zigbee application from nRF Connect SDK v2.5.1 to the Zigbee R23 add-on v1.4.0.
After migrating to the R23 add-on, I noticed that...
Hello Nordic Semiconductor Support,
I would like to request an RMA/replacement for an nRF52840 DK (PCA10056) that appears to have a failure in the Interface MCU/USB debugger...
Hi there,
I'm evaluating the latest release of NCS ZigBee addon version 1.4.0, wanted to try and migrate my existing project to the newer version. I've encountered the following...
Hello, our design does not use the USB block of the 52833. In the electrical schematic we have connected VBUS (AD2) to GND and we leave D-(AD4) and D+(AD6) open. Due to a...
When I create a new build ciónfiguration in nrf connect I get this Loading and the new configuration is not created itself.
This error is displayed in the VScode.
Could...
I am looking to evaluate Amazon sidewalk on the nrf54L15 dev kit and have also bought both of the Semtech evaluation boards LR1110MB1LCKS and SX1262MB2CAS. The nrf54L15 is...
Hello, We have a question about the errata workarounds applied in SystemInit() in nRF5 SDK v16.0.0. Our firmware is split into two images: a boot application and a main application...
Hi:
I use sdk ncs3.3.0 and nrf54lm20dk.
Failed to return using AA dfu_target_init.
OTA firmware is zephyr.signed.bin.
I: DFU header I: 3d b8 f3 96 00 00 00 00...
Hi, I am experiencing an issue where a specific nRF9151 SMA DK kit is stuck in an infinite network registration loop. The modem continuously reports +CEREG: 2 (Not registered...
