dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi,
I have fanstel BM833A modules which is NRF52811.
I am using Segger Embedded Studio.
How can i program the module through segger IDE using ST-LINK?
And also i have...
Multi link ble + zigbee multi-protocol testing is currently underway. The main purpose is to test the packet loss rate and throughput of radio time-division multiplexing zigbee...
We've had so many problem with Bluetooth Smart DFU on nRF52832 that I've decided to write a ticket here and ask for help. We've been reading lots of documentation, following...
We want to change the communication speed for each connected peripheral.
*Environment
Peripheral: nrf52832
Central: nrf52840
*Step 1. After the peripheral connects...
Hi all,
My project will use PPI to control COMP of nRF52832, connect Event of COPM and Task of GPIOTE.
Question 1,
How could I get the address of COMP event and use...
hi.
I wonder if nRF52840 dongle has an unchangeable bootloader, and if so, where we can download it. PCB of nRF52 dongle is available on the official website, but not in...
Hi there,
in my passion to keep up with technological advances, I ordered the nRF5340 PDK. I was hoping to pave the way of moving our nRF52832 and nRF52840 based projects...
Hey guys,
I'm working with a Laird BL652-SA Development Kit and downloaded the Nordic SDK v14.2.0. I want to try the UART example, but after the build comes a semantic error...
I'm not able to get working my PPK.
I've followed the guide, installed the Power Profiler app with the latest nRF Connect v3.3.0, cut SB40 on my nrf52840DK and set correctly...
Hi,
I wanted to know how to change the frequency from from 16Mhz to 64MHz which is processor frequency. I know the HFCLK is 16MHz but how to use the 64MHZ frequency.
Regards...
Installing the new nRF-Command-Line-Tools_10_4_0_OSX.pkg fails on MacOS (10.14.6). The installer gets to the summary stage and displays an error "please contact the supplier...
I can't find MQTT_LOG_LEVEL in the configuration interface in SEGGER embedded studio, but it is referenced when setting up all of the MQTT logging.
Where is this value set...
Hi all,
I have read a lot of posts here and didn't find any valid link to download J-Link OB firmware.
Does anyone know where to download this firmware?
Thx
Y...
