Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hi, I'm getting a crash when discarding an advertising packet.
Roughly what I do is:
Which crashes at advertiser_packet_discard().
GDB trace:
It looks like packet_buffer_pop...
When and by what logic Peer Manager performs garbage collection on FDS?
I have a single number stored also in FDS and I’m wondering if gc performed by Peer Manager will...
Hello,
I'm still just starting to deal with Zigbee and I have a question. I use 2 nRF52840 chips. One as a Zigbee Coordinator (CLI in SDK\examples\zigbee\experimental\cli...
Hello Sir
Sir i am try to sending the some text to nrf 52840 board,if you have any document please send it.
and how to do this process ? Sir please explain
Hi ;
If there is a ble message coming , but this time ble is getting data from sensor , what will happen ? Will it device reset ? Would you give me any idea to avoid this...
Dear all,
We have a question.
Did any body tried to make so that Bluetooth Mesh 4.2 works in PARALLEL with Bluetooth 5.
Some schedule reserved for BLE MESH 4.2 and some...
Hello,
I never used BT modules before. I'm going to buy some bluetooth modules to add wireless to an existing board.
I need module with following characteristics:...
Hi，I want to write the firmware to 52832 from android system by UART .I have readed the firmware into bytes, and then do not know how to compose the bytes to write into serial...
I have the following situation:
My device receives a number of RF packets, changes to TX mode, sends some data, goes back to RX mode and it should be able to access the...
Hi,
my application is normally a BLE scanner, listening for beacons. This runs OK.
Now, I tried to add a tested piece of connectable gap/gatt firmware, that runs fine...
Hi ,
in the RTOS example, you set
configTICK_SOURCE as FREERTOS_USE_RTC and configCPU_CLOCK_HZ as( SystemCoreClock ) .Since SystemCoreClock is 64mhz, why did you not set...
I am trying to understand why when I connect the nRF52840 Dongle using nRF Desktop I get this message in the log:
2020-02-26T23:12:13.293Z INFO Connectivity firmware version...
Hi Team,
We are using nRF 52840 chip for our development of product.
As of now the settings for BLE data transfer are as below.
MIN_CONN_INTERVAL 20 // which is the...
Hi,
I'm developing a router Zigbee device starting from light bulb example.
In the example the function zb_set_max_children is called passing 10 as parameter.
About...
