Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi I am working on activity detection using ADXL362 and nrf52. When I am moving the accelerometer ideally I should get activity interrupt in status register and when ADXL362...
Hi,everyone,
In my project ,I want to save some data when disconnect evt happens; here is my code:
the problem is ths program always stuck in power_manage() function; what...
I'm basing my schematic and antenna design using the PCA10028 as a reference.
I'm not including the J1 RF-connector into my design. Do I still need to include both C6 and...
I only hope that their devices can link their mobile phones, other mobile phone links may not link, but I didn't want to enter a password, directed broadcast method can, about...
I am using the nRF52832 as a MCU in the wearable device,now i want to use the spi master mode to collect data and store data ,and when it is necessary,I want through the bluetooth...
Hi
I have been working with nrf8002 chip. I simply want to program the hardware in a way such that it gives out a signal that can be detected by the emulator.
Hi Guys.
I have a little question.
I leave the bluetooth smart world one year ago, and now that i want to remake some project i read that there is some new.
So in my situation...
link text from this link i have some questions
(1) when i am trying to do step by step debugging ,debugger stops at sd_power_system_off();. can you tell me what to write...
@Michael Dietz
Hi, Michael & everyone. I'm using nRF51822 now. I followed the post Segger Embedded Studio & import the beacon example in SDK 10.0.0 . In Keil, the memory...
Hi, everyone. I'm focusing on SES with OS X for a long time. But there are always some faults and I have never succeeded utill now. I used to think OS X made these faults...
Yo Man,
I use nRF52 with example "ble_app_hrs_rscs_relay" in SDK11.
The printf only send one byte and I check other people asked question but still send one byte.
So.....
I want to test the Bluetooth signal performance of NRF51822 with frequency spectrograph,but Idon't know how to set a fixed frequency to NRF51822,I need your help
thank...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Hello everyone~
I'm setting up an eclipse and gcc development environment on Mac OS X following Vidar Berg's tutorial here: https://devzone.nordicsemi.com/tutorials/7/development...
I have some questions about DTM, can anyone help me ? thanks a lot!
1. I use DUT and nRF DK module to do the test. When nRF DK module enter tx test and DUT enter rx test...
