I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi,
I have 2 or more Thingy52 [SDK13 SD s132 v4.0.4], both of them are sending beacon every 200ms.
They have also the scan active, so they are able to detect the other...
I have merged two program SPI slave and ble_app_uart
I am getting these two errors
undefined reference to `nrfx_spis_buffers_set'
undefined reference to `nrfx_spis_init...
Hello,
I'm using nRF52840 dongle. I implemented a virtual COM port to send messages to my computer. My problem is that I can send messages only if I'm already connected...
Hello everyone, I ask for help to install the new version of SES in Ubuntu Linux 18, since the license is not recognized by the em nor the hardware, I can program the card...
After enter low power mode I aim to config to wake up on a 1 sec timer, but in 20 us the event 0x26 comes. I cannot find what event ID 0x26 is and how to disable it ?
Info...
I am having an issue when building the hci rpmsg example for the following youtube tutorial
Zephyr RTOS and Bluetooth LE on the dual-core nRF5340
I've tried figuring this...
Hello,
According to the description in below page, " The image can be an application image, SoftDevice image, bootloader image, or a combined image of bootloader and SoftDevice...
I am trying to interface adxl362 sensor with ANNA-B112 evaluation board.i am trying to read the part id to check the connection. The code is pasted below.
nrf_drv_spi_config_t...
Hi! I am using the 52840-DK dev board.
I want to use two pins, P1.0 and P1.1 as GPIO output pins.
In my code I have;
nrf_gpio_cfg_output(BLE_CONNECTED); nrf_gpio_pin_clear...
Hi everyone,
I want to serial print three float values (x,y,z) from an IMU. I use the MACRO NRF_LOG_ERROR( "Float_Value: " NRF_LOG_FLOAT_MARKER "\r\n", NRF_LOG_FLOAT(value...
Race condition in starting the ADC following calibration. I am trying to start the ADC in the interrupt routine when the end calibration is reported, however I have unreliable...
Hello,
I have two brand new nRF52 DK eval boards version 2.0. On both boards, the reverse charging diode D8 is missing. That diode is required to power the board externally...
Just trying to build Nordic sample codes S110 with nRF51822.
Here is the error. These are hidden file. I guess some configuration is not correct but I'm not sure.
---...
