after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi all.
I am new in nRF BLE. I am planning to buy an nRF51822 Kit but little bit confused with choosing EK or DK. Actually my plan is after playing with the Native Kits...
I am currently designing a board using the nRF51822 chip and I would like to implement a soft power ON circuit using the low power comparator (LPCOMP).
I understand that...
Hello,
I'm using a code posted on this forum to read ADC input and fill an array with the ADC values but I always get values between 166 and 174, (even if I connect the ADC...
I'm completely out of ideas.
I've been developing a server for some time now based loosely on the ble_app_hrs sample using the 5.2.1 SD. Things have been going reasonably...
After I process some data (command) received by UART fifo module (I have installed handler for APP_UART_DATA_READY) I need to do a short atomic operation of a few instructions...
We have a project where we would like to use a balanced / dipole pcb antenna. As far as the great docs on the site stands, it's all for unbalanced / monopole antennas. Any...
Hi,
In my application I need to control a nrf51822 central device by an external MCU.
Does Nordic provide solutions to control a nrf51822 Cental device (with S120 softdevice...
Is there a register, accessible via the SWD-DP and present across ARM devices, that I can use to distinguish the nRF51822 from other microcontrollers?
Thanks,
-c
I can discover RFduino BLE devices that use the 51822 using the Master Control Panel but cannot with the nRFTemp app. The nRFTemp app scans for but does not find my RFduino...
Hi,
I have nRFStartet Kit, nRF51822DK and EK.
What is nRF2739? I am just following the setup section in nRF51SDK and it says to connect Master Emulator to PC. Is it...
Hello,
I have been attempting to get the watchdog timer working in my project without any success. I have read through all of the watch dog related threads that I could...
The S120 is a pure Central softdevice, and hence it can connect only to other Peripheral devices. Does it means that s120 cannot be used as a peripherial device?
Hello all,
I have been using nrf905 for about 5 years without problems.
now I would like to ask if is there any way to use an external PA? I am not a RF engineer and i...
Hello,
I've an issue only on IOS. My custom service is recognized as immediate alert and crash when we want to use it. It works fine on android and with Master Control...
