Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I've seen the demo, but I understood that it wasn't really supported by the SDK at the time. Has a sample/demo been released for using NFC as OOB pairing with an (android...
I want to upload firmware from my desktop computer using some dongle. Is there any windows compatible nrftoolbox software? I am using the nrf51822 qfaag0 chip with softdevice...
In the function log_rtt_init(), the SEGGER_RTT_ConfigUpBuffer()/SEGGER_RTT_ConfigDownBuffer() can't config the customize buffer if the parameter buffer index equal to 0 (...
Hi all, i have loaded the example on my smart beacon kit (nrf51822 chip with softdevice s110), and it runs without problems. But in this example, the "normal mode" of the...
Looking at the documentation here (for SDK 11, s130)...
infocenter.nordicsemi.com/index.jsp
I see two conflicting statements
These APIs require that the...
The examples of whitelisting that I am looking at (ble_app_proximity, ble_app_hrs_c) both create their whitelists just before a scan. I am wondering if this is actually the...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
Hi,
I want to use more than 8 devices with gazelle protocol, so is there any way to expand the pipe number or change the pipe addresses in runtime ? Host device will know...
Hello, I have a problem NRF905. Sending distance is 0-30 cm maximum.
I want to ask if the defective product or it may be due code?
TX RX uses the base code of the library...
Hi Team,
In current application, each BLE node (nRF51x22) need to switch between Broadcaster and observer roles . Beacon kind of behavior is required i.e. no connection...
Hi All,
Please, I have some questions about the use of iPhone wireless shutter release button:
Q1: Is it possible to connect to an iPhone wireless shutter release button...
Open the nRFgo Studio and connect PCA10028 (NRF 51DK Board) then Erase all data
Open the uVision V5.18a
Open the DTM project file of the example in the following...
Refer to the NRF 51DK Spec page, It can be support Bluetooth 4.2 spec.
In the Bluetooth 4.2 spec, The device can support the maximum PDU size of 255 bytes
Where can I...
