Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I use the security mechanism dtls based on udp communication. Can I implement it on nrf52833? How much flash and ram should be occupied at least? Is there a suggested value...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hi,
nRF5340 and SDK v3.0.0 I'm using.
Currently my nRF5340 based BLE device can be bonded with smartphone via passkey, after bond is done, the device stops advertising...
hi everyone
After using Android nRF Connect FOTA, the settings storage partition of my device was erased, which means that my device's PAIR information was lost and the...
I'm having an issue with SPI communication. The problem is quite simple: if I use the Zephyr driver, everything works fine, but if I use the nrfx driver, it doesn't. The function...
Hello.
I'm having issues with a custom design board using NRF52832_QFAA SOC.
This is the snippet of the schematic design that my group created:
This board uses internal...
When selecting the ACLK frequency of 11.2896 mhz and a sample rate of 48khz, zephyr panics with the error "division by zero". The culprit is find_suitable_clock(). Posted...
Hi.
I've been developing with nRF54L15DK.
I added below in prj.conf.
Indeed, I could confirm CMSIS-DSP function normally running in main.c.
In my goal, I would like...
Hi, I am currently working on UART sample codes and have 2 nrf5340 Audio DKs . One acts as peripheral and another as Central. i want to modify the central board to connect...
Hi,
I'm currently using NCS v2.9.0 under sysbuild and have recently been using board definitions from different directories. My recent projects possess a "boards" sub-directory...
Hi, I've been trying to top up my iBASIS SIM card, but after clicking on the nRF Cloud SIM "Buy data" link it fails and generates a system error message (see image below)...
Hi all,
Has anyone implemented an MQTT client on an 54L15 before? I have been searching the web and I have not seen a sample program or anyone talking about MQTT with 54L15...
Hello, I've completed nRF Connect SDK Fundamentals Certificate of Completion but I've noticed a little problem with printk and logging.
When I use build configuration with...
Hello, I have nrf5340dk and AT21CS01-STUM10-T module. This is EEPROM module. I want to communicate with it by 1-wire. The problem is that I don't know how to do it. I looked...
Hi,
I was wondering if the newest sample available in NCS3.0.1 is already capable of holding multi connections. Otherwise, for this little time that is present i will...
This may be a silly question but for the channel sounding with range requestor sample the numbers following each method is the distance in meters right? I: Distance estimates...
Hello,
I am developing custom hardware based on this DK and am trying to eliminate circuitry that is unnecessary to my application. The DK includes a U20 load switch which...
Hi, I created a blinky sample for the ProMicro board. Entered the flash mode as mentioned in https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/boards/others/promicro_nrf52840...
Hey all,
I try to flash the SuperMini nRF52840 using my NRF52-DK over Debug HW (SWDIO pins). I try to flash the Zephyr blinky example.
I think I already got it (at least...
