Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Hi,
I have met return error below point when I try to upload Application Hex file with bootloader in nRFgo Studio Ver1.17.0.3211.
if (!(IS_WORD_SIZED(m_start_packet...
I am trying to get enhanced shockburst working with the nRF24LU and the nRF5188. I am using the nRF5188 as the transmitter and the nRF24LU as the receiver. I am using the...
hii...
i hv maufature_array of size 7 to advertise.... am facing a problem while advertising battery level service with dat... my code is lyk dis
uint32_t err_code;...
Hi !
Here my adv setting (slow interval) to advertise every seconds :
#define APP_ADV_INTERVAL_SLOW 0x0664 /** This value corresponds to 1022.5 ms).
#define APP_SLOW_ADV_TIMEOUT...
Just ordered another pair of beacon hardware and noted the nrf chip is now coated in black goop.
Curious as to what this is for, and the reasoning its been added to the...
Hello,
I have a master configured as "Bidirectional Master Channel" and a slave configured as "Bidirectional Slave Channel". Both talk to each other. When I start just the...
Is the DC/DC converter enabled when running ble_app_beacon?
Or is it only the LDO that is enabled?
I am running the application on nRF51822-DK.
BR Magnus
I ran into this last night and curiously, James appears to have posted about it yesterday ( devzone.nordicsemi.com/.../trouble-with-system-halted,but-cannot-reset-nrf51822...
I am trying to get the Heart Rate example in the nRF51 SDK to work (found in ...nrf51822/board/nrf6310/ble/ble_app_hrs). It fails at line 338 in main.c (at the call sd_ble_gap_device_name_set...
I'm putting some bootloader and static config data in the customer section of the UICR and I accidentally wrote to 0x1001200 and worked just fine.
Looking closer, it seems...
Dears:
We will adopt nRF51822 for our project, and we want to confirm with you for the question as below:
Does nRF51822 support HCI command protocol through either...
Hello,
I do erase flash pages in my application I use the sdk api:
nrf_nvmc_page_erase(firstaddress);
nrf_nvmc_write_bytes(address, data, len);
but I did not found...
