Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
The nRF51822-EK, when powered over USB, seems to be working on 3.0V. The C232HM SPI cable is a 3.3V cable. The nRF51 data sheet specifies VIO as VDD+0.3 as absolute maximum...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hi - I saw this post and I'm not sure how to add a clarifying question on to it:
devzone.nordicsemi.com/.../
We have a similar problem in that we built our boards with...
Hello,
I am working on an application that involves sampling audio data ~8KHz. I have a few questions
The real time clock module has a maximum interrupt frequency...
Hi everyone,
I bought two NRF24L01+ off ebay a couple of week ago and started to work on them this week. I seem to have problem with establishing a reliable communication...
Hi,
I use : An nRF51822 mbed kit + Kiel 5
So I updated the firmware like this : mbed.org/.../ and I dropped s110_nRF51822_v6.000 into MBED(H:)
I successfully use...
Hi,
i read about a new Chip revision of nrf51822. So i have to buy new Development Kit. How can i find out what it is the actual DK and where to buy it. I don't want to...
Hello All,
I was looking at the flash writewrite_example and the starting address is defines as:
addr = (uint32_t *)(pg_size * pg_num);
Later in the code, the example...
Is there any updated install procedure for the nRF51822 tools?
I'm trying to follow procedure in: nRF51822 Development Kit User Guide v1.4
I have the nRFgo Starter Kit...
Hi all,
In my keyboard application, I found sometimes it return the INVALID_STATE error code , when called keys_send() , once this error code appeared, no others return...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
I've looked over all the previous posts but none of them seem to work but the most useful one I can find is this one:
devzone.nordicsemi.com/.../
The code compiles fine...
Hi,
I'm trying to build the ble_app_beacon project for the nRF51822 (pca10001 board). Using default installation folders, latest SDK (v6.0.0) and Keil V5.1.0.0. I used...
Hi
I've made a small application on a NRF51422 device. It's is loaded with the newest version of S320 and the newest API from you homepage.
In my application i need...
