HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
I have recently switched to using SEGGER embedded studio (SES) which seems to be advocated by Nordic. I have arrived from Eclipse which though extremely flexible is complex...
Hello,
I am working with the nRF52840 dongle. There is a bootloader at the end of it's flash, which can be started by pushing reset after power up.
However I cannot start...
Hi Gene,
One of my customers using our module to pilot run.
https://static1.squarespace.com/static/561459a2e4b0b39f5cefa12e/t/5da77e178970da0cc270ef0d/1571257883383...
Hello,
I noticed that Table 7.3 of nRF52832_PS_v1.4.pdf states that 37 interrupts have been implemented, whereas the peripheral listing in the documentation as well as interrupt...
While advertising I could see some increased current peaks on one of the three channels. Its random and is observed mostly at the first or last channel of advertising.
Any...
Hi,
I wish to power optimize the proximity example application, as my intention to make a find-me tag. So I may not need the lls and tps services. Is any guidelines for...
Hi There,
I now have 4pcs PCA10056 and 4pcs PCA10059 for the development of our BT Mesh products by nrf52840 of Nirdoc. I have completed the installation of the tool chain...
Hi, I wanted to send data over Bluetooth 5.0 modules and to see on a terminal. So I used nRF52840 DK as central device ( ble_app_uart_c) and Fanstel modules ( ble_app_uart...
HELLO ALL,
I'M TRYING TO TEST THE BSC Rx EXAMPLE FROM DE SDK V16.
WHEN I DO IT USING ANTware II, EVERYTHING IS OK, SINCE IT'S ENOUGH WITH CONFIGURING CORRECTLY CHANNEL...
Hello,
This is a followup question regarding this old thread I started: https://devzone.nordicsemi.com/f/nordic-q-a/48295/hold-output-pin-during-bootloader-jump
IC: NRF52840...
Hi,
I'm relatively new to your product line, but have been spending a bit of time trying to bring the volume control functionality into a SDK16/PCA10056/s140 configuration...
Hi,
I am using SD calls to start an advertisement of BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED :
sd_ble_gap_adv_start(m_adv_handle, APP_BLE_CONN_CFG_TAG...
Hello, I have a project that's fairly mature and working great but now I want to extend the abilities of the device by using the extended PHYs. I know there are a million...
Hi
I plan to use nrf52 DK to program my device by using a connector https://www.tag-connect.com/product/tc2030-idc-nl
But should I connect it to debug in or debug out...
Hello,
background: using Keil IDE, my own board that has a nRF52840 on it. My goal is to create automatic DMA transfers from SPIM3 peripheral.
I am setting up EasyDMA...
