I am currently creating and testing a custom board equipped with the nRF9160 and the P822601 antenna. Considering future development, it is expected that another external...
Title: nRF54L05 issue after migrating from NCS 3.0.0 to NCS 3.3.0 with PM static partitions and MCUboot external-flash secondary slot Description: I am migrating a project...
I am currently designing a custom board for my nRF54L15 project and I would like to know if the "Antenna" pin on the nRF54L15 can have a DC path to ground/ground layer of...
I have a nRF54l15dk development board and a custom nRF54L15 board that I am trying to load a Matter Template sample application on. I have created a custom board device tree...
I have observed that when using the ESB protocol at maximum throughput, the measured power consumption decreases as the PHY data rate increases: 4 Mbps consumes less power...
Subject: Connecting LPCOMP CROSS event to TWO DPPI-driven tasks (GPIOTE toggle + TIMER count) simultaneously — only the last-configured one fires
Chip: nRF54L15 SDK: nRF...
Dear Nordic, i have started my application with toolchain & sdk both v3.3.0, using custom services & charachteristics, with BLE advertising @500ms interval works fine. but...
Hi there,
I'm trying to do a DFU over BLE using the Nordic nRF5x SDK on version 14.2. I'm using an NRF51 dongle on the PC side while trying to transmit to an NRF52832,...
I am using a nRF52 to communicate using both BLE and proprietary protocols. When using BLE, I apply the workarounnd for errata 102 and 106. However, when I switch to my proprietary...
Hi
We are using PCA10040 together with the ble connectivity firmware, pc-ble-driver and pc-ble-driver-py as a part of our automated test system. Eight dev boards are connected...
Hi,
I've been trying to update Espruino ( github.com/.../Espruino) from using SDK 12 to SDK 14, which is proving to be a pretty horrific task.
The latest issue I've...
Hi,
I am currently porting an application s110-based to s130v2.
Previously, I used to create critical sections using sd_nvic_critical_region_enter/exit .
Reading...
Hello,
I am using nrf52840 PDK, sdk 13.0.0 for my college project. I am trying to rewrite this nrf mpu example , in order to read data from MPU9255 and observe the data in...
Hi l trying to hookup arduino primo and BMI160,but recently my develop is in a strange situation,that i sent 0x00 and others register but alway return 0xff, here shows the...
I want to check if some errors happened during the initialization before entering while(1) loop in the main. I am using nrf_CLI in my application (SDK 14.2.0 and S140 on nRF52840...
Dear Nordic Team,
Tanks for Supporting.
How to start test DFU in SDK12.3.0. My Hardware is PCA10028.
How to merge hex files soft device and bootloader ?
update 1...
I need to count millis from nrf52 start
I have seen that all are using rtc1 but I did not find any example from which i can integrate it to my project.
We are in the development stage of a product that uses the nRF52832 and have acquired a nRF6707 Rev 1.1.0 power profiler kit to make power consumption measurements.
I am...
Hi,
I'm trying to download Invensense's "Embedded MotionDriver 6.12" in order to compile the Thingy:52 SDK, as suggested here .
It seems that this wasn't previously...
Hi everyone,
I am currently trying to implement USB headset on nrf52840. As far as I can see the audio example from SDK14 uses SyncType=None meaning that bmAttributes bits...
I want to change type from "uint32_t val1 = 0xAA01" to "uint8_t val2 = {"AA01"}.
Then, attr_char_value.p_value = val2;
=> sd_ble_gatts_characteristic_add(p_rms->service_handle...
I am currently trying to develop Mesh applications using the Nordic Mesh SDK and the nRF52840 Dev kit. The problem that I am having is that my testing equipment isn't able...
