I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hello,
I am not much of a PCB designer but want to tinker with nrf51422 EK Altium designer files provided. I try to open the project file using Altium designer 14, but...
Hi all,
I am new to hardware design and would greatly appreciate pointers. We intend to use mini-USB port for charging/power supply rather than for data. What is the best...
Hi all,
I am using NRF24LE1 32pin.
Does anybody know can I apply on XC1 pin external frequency different from 16MHz if I am not using radio module??? Thanks.
I am currently using the nRF51422 DK along with the nRFgo Starter Kit. I followed the instructions in the PDF "nRF51422_DK_UG_v2.0," and I attached the nRF51422 with PCB antenna...
use keil to download code to flash fail
use nRFgo studio to connect target device error
Load
C:\Keil\ARM\Device\Nordic\nrf51822_v5.0.0.34603_Backup\Board\pca10001...
Hello,
when using Keil's ULINK Pro debugger V1.57 connected to PCA10006 board for debugging nRF51822 code the ULINK is recognized by µVision V5.1.0.0 but the FW download...
I have an nRF51822 (256KB) that I want to program with some data targeted at 0x20000 to just under 0x38000. My code starts at 0x16000 (allowing for S110) and is only 1700...
I have a nrfgo 6310 start kit that I use for my nrf51822, but I'm wondering if I can also use the nrfgo 6310 for the nrf24Lu1 development kit as well? I tried plugging in...
Hi All,
I am working on the S120 bootloader.
I start it with dfu sample on nrf6310 folder. It work with S110 softdevice with PCA10001 perfectly.
I had made following...
Hi,
I would be grateful if someone could guide me a bit.
As far as I understand, nRF24L01+ implements Enhanced Shockburst technology in chip. To use nRF8001 as drop in replacement...
Hi all,
I am using s110 v7 for scanning and advertising, it works well. Now, I would like to measure RSSI while scanning (already scanned device but not connected) . Can...
Hi,
I am using nRF5182. Kiel is the IDE. I need to operate the device in 25Mhz. How can i change the clock frequency to 25Mhz. Is it possible? Will it affect the operation...
Hi,
I just stumbled upon the nAn-36 note ( www.nordicsemi.com/.../80193304 ) and I have two comments about it :
I think it's the best technical documentation I've...
Where to find definition for INTENSET/CLR for TIMERs in 'nRF51_Reference_manual v1.1'? I think I've read it all by now, but still can't find it.
After some digging I found...
If I have the PC insert 1msec byte spacing between data bytes sent to the NRF51422, it receives the message and doesn't reset. I can send messages less than 10 bytes to the...
