The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm having an issue with SPI communication. The problem is quite simple: if I use the Zephyr driver, everything works fine, but if I use the nrfx driver, it doesn't. The function...
Hello.
I'm having issues with a custom design board using NRF52832_QFAA SOC.
This is the snippet of the schematic design that my group created:
This board uses internal...
When selecting the ACLK frequency of 11.2896 mhz and a sample rate of 48khz, zephyr panics with the error "division by zero". The culprit is find_suitable_clock(). Posted...
Hi.
I've been developing with nRF54L15DK.
I added below in prj.conf.
Indeed, I could confirm CMSIS-DSP function normally running in main.c.
In my goal, I would like...
Hi, I am currently working on UART sample codes and have 2 nrf5340 Audio DKs . One acts as peripheral and another as Central. i want to modify the central board to connect...
Hi,
I'm currently using NCS v2.9.0 under sysbuild and have recently been using board definitions from different directories. My recent projects possess a "boards" sub-directory...
Hi, I've been trying to top up my iBASIS SIM card, but after clicking on the nRF Cloud SIM "Buy data" link it fails and generates a system error message (see image below)...
Hi all,
Has anyone implemented an MQTT client on an 54L15 before? I have been searching the web and I have not seen a sample program or anyone talking about MQTT with 54L15...
Hello, I've completed nRF Connect SDK Fundamentals Certificate of Completion but I've noticed a little problem with printk and logging.
When I use build configuration with...
Hello, I have nrf5340dk and AT21CS01-STUM10-T module. This is EEPROM module. I want to communicate with it by 1-wire. The problem is that I don't know how to do it. I looked...
Hi,
I was wondering if the newest sample available in NCS3.0.1 is already capable of holding multi connections. Otherwise, for this little time that is present i will...
This may be a silly question but for the channel sounding with range requestor sample the numbers following each method is the distance in meters right? I: Distance estimates...
Hello,
I am developing custom hardware based on this DK and am trying to eliminate circuitry that is unnecessary to my application. The DK includes a U20 load switch which...
Hi, I created a blinky sample for the ProMicro board. Entered the flash mode as mentioned in https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/boards/others/promicro_nrf52840...
Hey all,
I try to flash the SuperMini nRF52840 using my NRF52-DK over Debug HW (SWDIO pins). I try to flash the Zephyr blinky example.
I think I already got it (at least...
