I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi guys,
we have triggered one interesting state of fds module… This could be somehow connected to https://devzone.nordicsemi.com/f/nordic-q-a/27259/fds-data-corrupted/107629#107629...
I have a problem with upgrading bootloader on NRF52832 IC. We are in the middle of porting our own bootloader from SDK 8.1 to SDK 14, because we had to change BLE modules...
Dear All,
while evaluating low-power options in the context of wireless sensors, I've stumbled upon a strange behavior with the nRF52832 using ESB from SDK 14.2. Here's...
Hi
I modified the SPI master example to read an 16-bit ADC at 44.1 kHz.
While the HAL_TIMER achieves its ~22 microseconds quite good, the SPI driver is quite slow: the...
Hi!
I have an observer that listens for advertises from just one ble switch. I can control the leds on the nRF52 DK with the switch. Now i want to connect to nrf connect...
Hey guys,
I have been fighting with this for a couple of days and I am hoping someone can give me some insights as to what might be going on.
We currently use the nRF24L01P...
hi,
i am doing a project where i have to discover custom services on connected ble nodes.
i am using nrf52832 as central device and thingy 52 as peripheral device i have...
Hi Nordic:
I build up an mesh network with following setting:
1. A nRF52 platform with example/light_switch/provisioner with a auto-start-provisioner
2. Another nRF52...
Hi,
I have successfully used the nRF Connect app with a Rigado BMD-350 Dev Board to send a few UART characters back and forth to a new target device using the Rigado BMD...
I started today with the following examples to make a start with serialization:
- ..\examples\connectivity\ble_connectivity\pca10040\ser_s132_hci
- ..\examples\ble_peripheral...
HI:
I am Measuring current on custom hardware with nRF5x DK, Peak current is always too high during testing.Please give me some advice。
I am using the nRF52 DK development...
Hi,
I am working on RTC implementation. I had a doubt.. Is it possible to generate interrupts on different channels (channel 0/1/2/3) using same RTC instance ?
Thanks
Hello,
I'm trying to communicate with another device via I2C. I'm trying to do a simple write but it seems that the TWI NRFX driver is sending wrong data.
I'm just calling...
Hi,
I am implementing a beacon solution and intrested to move from fast to slow and vis versa(slow to fast) advertising modes -
i.e. BLE_ADV_MODE_FAST & BLE_ADV_MODE_SLOW...
Hey,
I have seen some articles which says that voice over BLE (4.0) is possible but there is no standard profile for it.
So far i've seen :
Silicon Labs
STM
T.I...
