When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
I need to stream 2 audio channels between two nRF52832 chips. I have two of the nRF52-DK boards and would like advice on which sample app might get me started in the right...
I have used 32khz and 32Mhz Crystal and across that crystal i have used 12pF capacitor. But unfortunately in market 12pF capacitor is not available in 0402 smd package.
...
In the SDK, there are examples for boards called "pca10028, pca10040, pca10040e, pca10056"
I have the nRF52-DK board, which of the above numbers does it conform too? Or...
Hello,
I am trying to adjust a peripheral device to connect a central device based on ble_app_uart_c example. Although this example has been discussed numerous times I was...
I am moving an SDK12 peripheral nus + central nus application to SDK14.
I am following the ble_app_hrs_rscs_relay example for SDK14 on how to setup the dual role ble event...
The nRF52832 OPS 0.6.3 describes the CONFIGID register in FICR. This is the same as on the nRF51822.
SDK 14.1.0 does not show this register in the NRF_FICR_Type definition...
Hi everyone, I've read some nordic forum articles on this topic but somehow I just dont get information I need.
I can flash my custom nrf51822 chip by using my nrf51422...
Hi,
I'm currently evaluating the use of the nrf52832 as an HCI interface with a linux host and realized from the various questions that the nrf SDK does not support the...
I am running on Uvision. 5.23.
I am running a Central on one PCA10040 DK and a Peripheral on a second PAC10040 DK.
When I run a first RTT Viewer V6.22 (with SWD Target...
Below is from SDK14.2.0 ble_gap.h
There is no white list variable.
/**@brief GAP scanning parameters. */ typedef struct { uint8_t active : 1; /**< If 1, perform...
I am developing a general case application for several devices I am developing. The application template will then be modified in small ways to support different hardware...
Hello everybody, I try to send nus_string data. I bought different inputs and outputs like this;
INPUT;
OUTPUT;
"aaaaa" received // Send 5 times "a"
INPUT;...
Hi team,
I looking for an example on how I can setup a mesh to send and receive string of characters from and to mesh nodes.
I have couple of nrf52832 modules connected...
