Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi there,
So I'm going through that complicated step of setting up the IDE for the first time to get started programming and I'm having issues doing it with the SES and...
hi everyone ,I want to ask you a question, I use the SDK12.3, when the device from the application transformation to the bootloader, when DFU is failed, why the deice is stays...
I am using nRF51822 (PTR5518A) with SDK v12 and s130 softdevice. To dump the code I am using nRF52 DK segger (PCA10036). With that I am able to dump the code but there is...
Hello ,I hope the speed of NUS can be achieved 7K Byte/s. The data form phone to uart is ok,but the data form uart to phone is not.I tested the Bluetooth part separately.Loop...
Hi,
I am able to connect nrf51822 with nordic app but now i want to receive data from nrf51822. For Example -
If nrf51822 detects some voltage at pin no "1" then it should...
Are there any Segger Embedded Studio examples for the nRF51 dev kit?
All the examples supplied with the nRF5_SDK_14.1.0 seem to be for the nRF52.
I only bought a new dev...
How do you do
E: \ Nordic \ nRF5_SDK_12 _f012efa 2.0-3 d \ examples \ peripheral \ pwm_driver pwm_driver routines of the path,
1.How to configure reverse polarity...
In all the SDK examples all the source is in main.c. Is there a good reason for keeping everything including timer initialization, UART config, BLE setup, etc all in one file...
Hi,
I am using nrf51822 (pca10004) with SDK110 softdevice programmed through j-link LITE SEGGER. After programming the custom code (Basic I2C code) and when we try to debug...
Is there any documentation as to how to connect a nrf52 chip (as found on the nRF52832 BT Module with Header Pins ( www.analoglamb.com/.../) or the nrf51 on the Adafruit bleFriend...
Hello,this is Lee.I have a problem about nRF51822.
When I turn on/off the power 2.8V to it ,it hangs up
frequently.I check POR function,I found that the residual
voltage...
hi,
i'm using the 32KHZ external crystal and i didn't find any free space in my PCB to put the crystal in the same side with the nrf chip, so the only solution that i found...
I am trying to implement a bootloader with rewrite protection on nrf52840 with SDK: 14.0.0.
But it seems that there is no flash write protection registers in nrf52840.
So...
UPDATE: Corrected language.
Hi,
While experimenting with BLE mesh networking using S130 on nRF51 devices and S132 on nRF52 devices, we have a problem with deafness while...
Hello,
I want to save Image data which are come from the central device to flash memory of peripheral side.
The image data size is vary from 3KBytes to 10KBytes.
...
