When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I am using IAR for the pca10056 with a nrf52840 chip. Can I change the compiler in IAR? I simply just downloaded the newest version from the IAR homepage and specified...
Hi I'm trying to compile the experimental_ant_bootloader for the pca10040 with a S212 soft device using the armgcc compiler using SDK13
I can't find a makefile or linker...
How do you do
1.In the Nordic \ nRF5_SDK_12 _f012efa 2.0-3 d \ examples \ peripheral here, there are three PWM routines:
Low_power_pwm, pwm_driver, pwm_library but only...
Hi, there~~. The PCA20006, nRF51822 Bluetooth Smart Beacon Kit, is fascinating!
So I'm planning to create a custom beacon product of my own,
a 2-layered PCB with nRF52832...
I have trouble programming the PDK using nrfjprog. I can flash the program fine using Segger Embedded Studio but it doesn't appear to be working using nrfjprog.
Here are...
When using ble_app_uart, I set the advertising timeout to 10s, but after the timeout did not enter sleep, but automatically reset,my judgment is based on the terminal to send...
Hi
I have run this example code
nrf5_SDK_for_Mesh_v0.10.0-Alpha_src\examples\light_switch\client\light_switch_client_nrf52832_xxAA_s132_5_0_0.emProject
when I operate...
I want to reprogram a nRF51822 xxAC device on a existing product.
I have a J-Link (SEGGER) device with latest firmware.
I'm running the SEGGER J-Flash V6.20e utility.
I...
Hello,
I have constructed a custom board with nRF52832 and MPU9250 on it.
I have flashed the program for reading battery service, temperature service and MPU9250 readings...
I followed the tutorial on devzone.nordicsemi.com/.../ to use Eclipse, GCC and GNU Debugger.
I encountered an error after the successful build (with key symbol) with CDT...
Hello,
I purchased nrf51822 module and i want to use s130 sdk for my project.
But when i have look over using keil i found that it requires jlink debugger or jtag debugger...
I am studying about developing a simple BLE 6LoWPAN network. My proposed topology is mentioned below:
internet - - - - - - - - - BLE1 - - - - - - - - - BLE2
| \
...
Hello,
As we can see, the mesh stack is a totally new stack which is independent of traditional BLE stack. Could you please explain why to design like this?
I found there...
Hi, I'm deeply interested about the Nordic's PCA20014; a.k.a solar beacon .
This HW uses
Amorton AM-1417CA solar cell, 1.5V, 12.5uA at FL-200lux
2 channel...
Hi,
I have run into a problem with the nRF sniffer. I used it in late May and early June to debug a BLE connection between a nRF-DK and a HTC Desire 610 and it worked fine...
