We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hello,
I am having a trouble with my code. There is an RTC sensor Which has the address 0x32. When the sensor is connected to the TWI lines, there is no problem and it...
Hi There,
I've been developing a product using the NRF52DK. I had some custom PCB's made after I had my circuit designed, and I programmed them with the NRF52DK. Now my...
This one is weird. On a new board with a Rev C '840, when trying to reset the processor using 'nrfjprog --program nuttx.hex --sectorerase --erase', a Decawave DW1000 connected...
I want to add ANCS client to my code. Like in the ble_app_ancs_c example, I start a timer after BLE_GAP_EVT_CONNECTED. The timer handler calls pm_conn_secure() if the connection...
Hello
SDK12.3, nRF51822
I'm trying to interface the ssd1306 the program freezes in function app_twi_perform internal_transaction_cb is not called internal_transaction_in_progress...
With our nRF53832 device we are not using NFC.
For the lowest power usage should I keep them as disabled NFC pins or change them to GPIO pins and drive them to the same...
Hi!
I have a question regarding nRF51822 supply in internal LDO setup. Is decoupling capacitor on pin DEC2 necessary in this supply setup? Looking at schematic in nRF51...
Hi! As far as understood, there are only 2 clock cycles before the Watchdog timer reset occurs. Is there a way to change/set this to a different value? I need to write in...
Hello!
When using the NRF_LOG module along with a JLink, when I connect the probe to the nRF the RTTClient prints out the first lines that were written when the probe was...
i comple the ble_app_proximity in SDK15, Config APP_ADV_DURATION for 10s,after timeout, no BLE_ADV_EVT_IDLE occur in on_adv_evt.
how put the system into sleep mode?
Hi,
how can i merge ble_app_beacon with mesh sdk beaconing example?? I want to advertise sensor data into beacon advertisement packet. all beacons should be formed a mesh...
Hi All,
I am trying to use TWI on NRF52832 using SDK 12.3 + SD132 but without any success.
For some reason, there is no signal coming out on the configured SDA + SCL pins...
Greetings.
I have PCA10056 0.9.3 and have downloaded nRF5_SDK_15.0.0_a53641a. I am trying to run pre-compiled ble_peripheral examples. I have tried ble_app_blinky and ble_app_uart...
I can connect the board to the Pi and ping it with a globally valid IPv6.
When trying to connect with the MQTT broker, however, no package is sent from the Chip to the Pi...
