I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hi,
I would like to connect nearly 20 heart rate bands to the nrf52832 which has to configured as the central board and has to collect all the heart rate data from the peripherals...
Hi, I have a problem with my custom PCB.
Im ussing Segger in Mac, the latest sdk (15.02) and the latest softdevice too.
I have a custom pcb with a buzzer and when...
hello,
I faced interesting problem which I fortunately solved and would like to share with others because I hadn't found any information on this.
I am using nRF51822 on...
Hello,
we are currently trying to create sensor networks with the nRF52840 Dongle . Our first RSSI measurements in the field show that the orientation (rotation) of the...
My Software as follows: nRF52832 DK(pca10040) nRF52 SDK15.0.0 mesh 2.1.1 SEGGER Embedded Studio 3.12
I want to transplant "examples\peripheral\pwm_library" to "examples...
Hi,
We have a firmware application using SDK 12.3 and Softdevice S132 V3.0.0 running on a nRF52 controller.The firmware is used pheriperial BLE device and provides a GATT...
I am working on ble_app_hids_keyboard example code. I downloaded the bin file in my eval kit and tried to connect the Nordic_keyboard device with my android device. Then,...
Looking at the "Pin assignments" section in nRF52840, I found that some GPIO pins are recommended for standard drive, low frequency I/O only. I am wondering whether there...
-SDK: 15.0
-S132
-nRF52832
-Segger studio
I'm trying to implement bonding/whitelisting to my project, which is a connectable beacon with a custom service. What I want...
My Software as follows: nRF52832 DK(pca10040) nRF52 SDK15.0.0 mesh 2.1.1 SEGGER Embedded Studio 3.12
I want to transplant " examples\peripheral\pwm_library " to " examples...
I need to change, on a time basis, the advertising packet :
Let's say for X seconds it has to work as a "iBeacon"
BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
Hello,
We want to build Expiremental examples in BLE Peripheral.The Common issue which we have faced in bulding any of the Expiremental BLE Peripheral issue was the missing...
Hello. I am using the custom board (buttonless) of nRF 52840 to verify the services of DFU and NUS. After firmware rewriting with DFU, I confirmed that BLE communication with...
Hi,
Our Application software running in Micro is communicating with BLE over UART.
So in nutshell, we are using serialization to speak with soft device present on NRF52810...
