Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I need to connect VL53Xl to NRF51 DK> I am using latest 12.2 SDK with Keil MDK.I cannot find any I2C(TWI) example. I can find examples for NRF52 based devices. but not for...
I am using a nRF52832 which act as an observer role only and what is observe it send observed data to another device over UART.
When i turn off scanning and just run UART...
Hi,
I generally use " make flash" (armgcc makefile). If there are multiple devices connected I get a pop-up to select a device/emulator to be flashed. This pop-up just defeats...
Hi there,
I'm trying to use nrfutil generate package with an extern key pair generated with openSSL.
I used opneSLL with prime256v1 curve, which correspond to secp256r1...
Hi,
I use nrf51822 with HF XTAL Frequency of 32 MHz
I am migrating from SDK9 S110 to SDK 12.2 S130 and have a problem that the code stop on nrf_delay_us.
#ifndef...
we wrote a small application to jump to a desired address of our application from bootloader , but UART does not seem to work(i cannot see any transmitted values on terminal...
Hi,
I would like to use the ble_app_hrs to send pressure values via the heart_rate_measurement_send function.
Unfortunately, they are too long: around 105000 Pa (equals...
Hi everyone!
I have an application based on experimental_ble_app_eddystone for nRF52 (SDK12.2), which uses FDS to save in flash memory. Now I want to add the secure_bootloader...
Hello on git hub you add pc-ble-driver
but there is only help how to install it. I did not find any example. And I did not find any documentation how to use it or what is...
Preface: I am developing a software working with different radio protocols (enhanced shockburst, bluetooth,...). Therefore I implemented uart commands for switching radio...
Recently i have purchased nrf51822 and nrf51dk but i dont know how to flash softdevice in nrf51822 using nrf51dk.
please expain me how can i flash or where can i know how...
Hello,
I have a problem running nRF51822DK with temp. sensors while running BLE. I tried DS18B20 but it doesn't work at all, then TMP36 with ADC reading and as it works ...
I have spent almost one day trying to make sense of that.
NRF52832 is SPI Slave, based on your examples/peripheral/SPIS/pca10040 sample
SDK v12.2.0
board DK PCA10040...
I am trying to implement IR reception using TSOP1738, more specifically Vishay's SM0038.
I have set the GPIO pin to call an interrupt whenever there is any change in the...
