Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
we are using the nRF5340 with the nRF21540 (Fanstel BT40N module). I understand that different regions allow for a maximum of +10 dBm or +20 dBm in transmit power dependng...
Hi All,
In reference to my earlier ticket( https://devzone.nordicsemi.com/f/nordic-q-a/120183/question-on-immutable-bootloader-support-for-nrf54l15 ), I see SDK version...
I am using custom board with MDBT53 and I'm stuck at a point where board does not even let me to connect the debugger so that I can refresh firmware.
I added MCU boot code...
Hi, I have changed Vdd from 1.8 V to 3.3 V but now I cannot flash anymore my board (nrf5340). This is the output error:
* Executing task: nRF Connect: Flash: AppCore_RHS_SD_UI_v1B...
Hi,
a couple of days ago, I had to install some STM plugins for VS Code (I'm sorry ).
In the process, the "CMake Tools" from Microsoft were also installed. I remember...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
I have a USB HID device using the 'old' USB stack in Zephyr. I have configured the 'CONFIG_USB_DEVICE_REMOTE_WAKEUP'
1. I put the HOST to Suspend
2. The NRF52 USB goes...
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
Hello together, Which configurations or setup on the side of the Nordic nrf9161 DK has to be done to use the DEBUG IN connector for SWD? The board is powered by the 5VIN pin...
Hello,
In ncs, I am working with \nrf\samples\ipc\ipc_service. I want MCUboot to build \nrf\samples\ipc\ipc_service\remote to run on nrf5340 CPUNET. When I CONFIG_BOARD_ENABLE_CPUNET...
Hi,
I am working on Temperature sensor MAX30208 using nrf52840 using zephyr. i am working on ncsv3.0.0 . I want to develop a driver for max30208 . can anyone guide me how...
Hi,
I need to use the GPIOTE with interrupt function with nrfx ( https://github.com/NordicSemiconductor/nrfx/ ) directly on the nrf54l15 DK board.
So I created a build...
Dear Nordic DevZone,
I'm encountering pairing issues with mobile devices and a nRF54 DevKit flashed with HCI over UART firmware. After initial pairing, deleting the bonding...
I am trying to get the BMI270 working with a nrf5340 DK. I have read Unable to Connect nRF5340DK with BMI270 Over I2C - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi...
