I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hi
this is the code I'm trying with my buzzer,
I want it to generate sound but with different frequencies.
".base_clock = NRF_PWM_CLK_1MHz," I can only as low as 125kHz...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). I am trying to combine the examples ble_app_uart...
Hello.
I am trying to run the throughput example for the Connect SDK, using a 52840 DK and a 52833 DK.
https://github.com/NordicPlayground/fw-nrfconnect-nrf/tree/master...
With sdk16 cli, each command displays help message when used with -h option. It would be nice to have a help command which can display all active commands and their help ...
Hi,
I would like to use raytac MDBT50Q-U without an 32 mhz external crystal.
Periphal examples like "blinky" work but ble does not? nrf_sdh_enable_request fails with invalid...
Hello,
I am using SDK SDK_15.3.0_59ac345 with soft device in application that controls a GPS IC from UART (AT command), also the application is running in background beacon...
I refer the following the link . https://devzone.nordicsemi.com/f/nordic-q-a/33606/updating-advertising-data-manuf-spec-data-in-sdk15
I understand the adv data update. I...
Dear Sirs,
I would like to use in my program computed heart rate as a parameter.
Could you please give example how can I get to this value? I just found in page_0 such...
Hello,
I'm trying using \examples\ble_peripheral\ble_app_uart on PCA10040
I'm programmed s132_nrf52_6.1.1_softdevice, using nRF5_SDK_15.3.0_59ac345 with pca10040_s112_nrf52832_xxaa...
Hi,
Why is it that when NRFFW[0] = 0xFFFFFFFF SVC calls are passed on to the softdevice but when NRFFW[0] = 0x19000 they are passed on to the SVC handler of the application...
Do you have template for nRF52832/PCA10040 with s113 ?
If no, what have to change in my template for nRF52832 that works with s112:
c_preprocessor_definitions
S112...
My problem is a little bit weird: I don't get a HardFault, although I'd want so.
SDK-12.3.0 (d7731ad), FreeRTOS (from the SDK) and SoftDevice S130 (2.0.1) also from the...
Hello,
for the project I'm currently involved I'm developing additional components and changing/fixing parts/issues in the nrf5x SDK.
My client allows me to opensource...
Hi,
The examples in the SDK 16.0 for the nRF52811 all use the s112 and I woul dlike to have a NUS board (peripheral) with coded phy to talk to a nRF52840.
What are the...
Dear All,
I have a simple push-button.
Vcc-100k resistor ->> Push button --> Ground.
When I measure the current consumption when the button is pressed i get around 230...
