At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello,
When I added the below lines I get some error:
NRF_BLE_GQ_DEF(m_ble_gatt_queue, /**< BLE GATT Queue instance. */ NRF_SDH_BLE_CENTRAL_LINK_COUNT, NRF_BLE_GQ_QUEUE_SIZE...
Hello,
I have been looking through Nordic's documentation for the nRF9160 and trying to find voltage ranges for several pins but am having no luck. Can someone please answer...
iOS is using queued writes to send data to my nRF52832 application. For some reason, on the third queued write reply (in nrf_ble_qwr.c) sd_ble_gatts_rw_authorize_reply returns...
I'd like to build a prototype using the nrf9160DK that samples audio from a microphone and plays it back. Given that the dev board has Arduino compatible headers, I'm assuming...
Hello,
we are trying to add log functionality to our application (nRF52 SDK 15.3 SD6.1.1) and we have few questions:
1. can two uart and flash backends coexists in...
I'm trying to do step-through debugging with the nRF9160 DK using Segger Embedded Studio and it's jumping all over the place. I assume this is due to optimization but perhaps...
When bluetooth only is enabled, the program has no problems. After adding USB, the program crashes。 How am I supposed to initialize it, is it a matter of order
<info> app...
Hi,
I'm currently trying to use advertising extensions with my nrf52832. However once I use the
BLE_GAP_ADV_TYPE_EXTENDED_CONNECTABLE_NONSCANNABLE_UNDIRECTED
type...
Our device uses an nRF52840 and we are using SDK v15.3.0 and soft device v140.
In order to optimize power consumption, I want to make a delay function using the RTC (with...
Hi,
We are designing a device based on nRF52840 that implements the Zigbee ZBOSS stack. We are interested to get ZB NVRAM configuration (network id, bindings, reports, etc...
After not having used my Thingy52 for a number of months, I decided to get back to tinkering with it.
When switching it on, it briefly shines a red light and nothing else...
Hello,
I am using the DWM1001 board and would like to receive some bytes over UART to the nRF52832.
I want the device to wait for a certain number of bytes from UART and...
I am using BLE UART and want to incorporate BLE bonding so that IRK keys get exchanged and can resolve the advertisement packet. I am planning to use privacy mode.
Can you...
Hi, I have followed the steps of generating a new .h file for my custom board (save as of the PCA10056.h board, modify the file, then generate a new macro in preprocessor...
