Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hello, I'm pretty new to Nordic devices but I have already some experience with other ARM based devices though...
I'm playing with Timers bare metal instructions and figured...
Hi
I am currently trying to get the antenna switching working on the nRF52833 DK. I have an SPDT RF swtich which I want to use for switching between two antennas. I want...
Hi,
I've already asked this problem few days ago, but I couldn't figure out the clear answer.
The above figure shows the VDD values of BLE chip. The power supplied...
0> <debug> nrf_sdh_ble: BLE event: 0x26. 0> <error> app: Fatal error
I started with the nrf_tempelate project and used nrf_uart to add uart service. It works fine but after...
Hi,
I want to know that, can we use this nrf91 for transferring the real time data with tab or mobile phone beyond BLE range. I mean, do we analyse the real time data from...
Hi:
I have no dongle or any other Dev board such as PCA10031. Can I use nrf51822 and cp2102 as a usb dongle to work with MCU of PC? If the answer is yes, what should I do...
Hi All,
I am trying to decrypt some data coming in on my board with AES ECB mode. I know that there is no decryption function for ECB and you have to use the same sd_ecb_encrypt...
Hello, We are completing a project where is used the BLE device nrf52832. The product is composed by 2 devices: a peripheral and a central (both with nrf52832). The broadcaster...
Android update its repository android.support to androidX, so Nordic sample code of nRF_UARTv2.0 must do some editing to be a exectable code with the App,
Now we have met...
Hi,
I've developed nRF52832 chip for our company's application,
and I found some weird phenomenon
we using nRF52832 chip with Nordic softdeivce and SDK v12,
BLE...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
To reduce current I disabled NRF_LOG_ENABLED...
Hi,
Recently we have bought Thingy91 PCA20035 devices and tried to add to nrf cloud account but we end up with issues.
We followed the standard procedure to add the device...
Hi,
I'm trying to do something (seemingly) VERY simple:
I want to increment the count in Timer 2 every time a GPIO pin (17) goes from high to low, without using the CPU...
Hi. I'm programming a nRF52832 with a simple "HelloWord" code that just blinks two led. This code was created by MBED and loaded by SEGGER J-Link but I'm having some intermittent...
Misc info:
1. SDK Version: v15.3
2. SD: 6.1.1
3. Toolchain: IAR v7
I'm trying to use secure_bootloader from the examples but it's taking higher current upon power...
