Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Are there any migration guides for a customer who wants to migrate from nRF5340 to nRF54L15? And if they are nRF54L15 in chipscale, anything they should be aware of including...
We need to sense temperatures in the upper end of the operating range, specifically in the 40C to 70C realm. We have three different units, and we are finding that the temp...
Hi,
We're evaluating NFC for our project.
I've been testing with a nRF52840DK - PCA10056 Version 3.0.2.
Using the antenna supplied with the Development Kit I am...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hello - We're designing a new app for our product in Flutter. I was writing the proof of concept for the firmware updates, but I hit a roadblock with a Mcu Mgr Error: 25 ...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
When we were using nrfjprog to flash, we used "west flash --erase" because it was quicker to erase entire flash then sector by sector. However, when we upgraded to SDK 3.0...
I am using nRF54L15 with Zephyr to measure voltage with ADC. In the struct adc_sequence there is a calibrate bool, but I am not sure what it does. What is the reference that...
Hi,
Does Central or Peripheral UART enable ACK/NACK in the code for BLE communication? How does Peripheral recognize if Central has received all the data ? Is there any...
nRF52832, SDK17.1, s132 I work with SPI and it works on the this project with SDK15. But I have transferred this prj to the SDK17.1 and I can't make SPI work. I don't get...
We have a product which is based on nrf52840 and nrf connect sdk 2.8.0
After OTA sometimes, I find that the NVS is erased, which could lead to some issues on client side...
Hello, I am working on a project using zephyr as well as the nrf5340 MCU. For this test, I am on the nrf5340dk. My application requires I drive a PWM at 125khz. In my device...
I opened up the nRF Connect for Desktop application and noticed a new version for the SDK , 3.0.0. I also noticed that the application is being deprecated.
Inside of Visual...
I am trying to get my nRF9151DK connected to Azure IoT Hub. I have used the Azure IoT Hub sample, with some modifications to use LTE instead of WiFi which does not seem supported...
Hello, So I am working on implementing Bluetooth DFU OTA capabilities to send an image from a 54L15, acting as an SMP Central Client, to another 54L15, acting as an SMP Server...
I would like to use native CMake rather than West to take advantage of CMake Presets.
I have been able to make this work on the command line using the following command...
Hi , am developing the st7789v_minimal_sample application using Nrf52840. after creating minimal application am facing some unrecognisable issue. which am stuck can you please...
We have encountered a problem in using iic to communicate that the delay cannot be removed.
We are using the sample in NCS,
the address of the sample is C:\ncs\v2.6.1...
Hi,
I switched to SDK 3.0.0 and got back problem, that I had some time ago with 2.6?? When my code compiles, but controller stuck after many successful builds and I open...
C:\ncs\v2.6.2\nrf\samples\nrf5340\empty_app_core>west build –b nrf5340dk_nrf5340_cpuapp –p
while building the image, getting error:
ERROR: source directory –b does not...
