here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hello Nordic
Using the old SDK, i was able to do FOTA wiht 10kb/s.
After doing all kinds of tweaks, I am only able to obtain 5kb/s with the new connect SDK.
Can i...
Dear Nordic-support,
I am trying to use the modem_battery_low_level_handler and modem_battery_low_level_set(), but I think there are two different ranges for the battery...
Hi,
I need to enable an input interrupt on nRF52832 and I want to use a GPIOTE EVENTS_IN channel.
During boot configuration, I'm using nrfx_gpiote_in_init function with...
Hello Nordic support team,
Forgive me if I am asking a stupid question.
In the source file ble_conn_params.c, there is a function called ble_conn_params_init() and I...
I’m writing this post because I’m experiencing a problem with data transmission between two devices—a sensor and a USB dongle connected to a PC—each equipped with a Minew...
Hello,
I am studying the materials in Bluetooth Low Energy Fundamentals.
I cloned the codes from GitHub https://github.com/NordicDeveloperAcademy/bt-fund
I tried to...
I have set up the OTBR with a RPi 5 and an nRF 52840 DK as an RCP. The CLI device can join the thread network as a child, the OTBR as the leader.( https://www.youtube.com...
Hi,
With several nrf52840 based prototypes, I had serious problems. I could see them die after flasing them a few times. And this was not just one dying, it was all of them...
I am currently developing a firmware application on the nRF5340 where I need the device to function in dual role :
As a Bluetooth Mesh Node , communicating with other...
I am getting an error of "undefined reference to `pm_state_force" .
Also, the output files, config file is not showing the command : CONFIG_PM =y
prj.conf file has : ...
Hello Nordic Support Team,
I have three queries to make.
Is it possible to force the channel in which the data transmission is happening using nRF52840 DK.
To explain...
Hi all,
we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
Hi,
why antenna trace is connected to mounting pad instead of feeding pad of antenna in thingy 91x
We are designing our device based on this. We wish to be sure about...
Hi Team,
I’m using the nRF5340 Development Kit, and in our project, we have a custom slave device that communicates over QSPI. We’d like to interface this custom device...
Hi
I am trying to setup and test the OpenThread CSL feature on nrf52840DK with OpenThread daemon and RCP mode nrf52840DK.
I found there is a way to build the Daemon for...
