Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello, we would like to release our product to the market.
Our device is a (BLE) beacon based on nrf52 which is advertising some data encoded as manufacturing specific...
Hi everyone!
I have probelem with receice data over UART. In the other MCU use core ARM as : STM32, NXP... when a byte is recieved, MCU has flag to notify. That is "interrupt...
My code is in the link attached:
github.com/.../master
With that code we have a current measurement of 1.1mA. As you can see in the code, we have tried to disable all...
Hello guys, i am Dani.
Actually i am new in hardware communication and i have problem with BLE - Android Pairing.
The details are as follows:
I was trying to perform...
Hello,
As per my requirement I want to develop a device that would be capable of sending & receiving data to & from a web server & at any point of time multiple devices...
Hi everyone,
I am using board PCA10040 v1.1.0, softdevice 13.0.0, Eclipse Oxygen. I am trying to connect my board with a device call Daydream controller .
There is also...
I am seeing this warning flag on almost every files in Keil projects in the nRF51 SDK v10.0.0, be it original unmodified examples or projects that I modified from such examples...
If I want to get 16kHz output sample rate of PDM,then what should I do? How to cofigure the register PDMCLKCTRL and the clock HFCLK? Could you give me more details? An example...
Here are 4 broadcast signal, the first is send with dfu, whenever how I try, it only display 8 characters in max.
And the second and the fourth named begin with "LOCK_...
Hi,
I have a question about my schematic.
In the datasheet I've read that it doesn't matter which pin is used for several pheripherals like SPI.
So does this means...
Hello,
I am using 12 bit ADC in my application but data element more than 8bit is not send correctly, Also not receiving Array[10000] element. I am using nrf52.
Thank...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Hi,
Let's assume that we know there is a packet ready to be sent every 20ms. Now what is the best connection interval from power consumption point of view? Here is my understanding...
