Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hi,
currently trying to boot up mcuboot with nrf54l15 pm_static for both cpuapp and cpuapp_ns. Both files are included in the zip file.
I have already tried several configuartions...
Hi,
I'm using nRF9160DK with SDKs v3.0.0
I am trying to use A-GPS with nRFCloud REST. I used the location example and it works correctly. The documentation states that...
Hello,
I am new to modems and cellular domain.
We intend to design and build a cellular communication extension for an older product. And I eyed the nRF9151 for that....
When my program hits an error returned by an NRF API call, I get a hex number corresponding to that error from the app_error.c:
case NRF_FAULT_ID_SDK_ERROR:
m_error_data...
We've got devices that are out in the field which were built on SDK6.1 w/ 110 SoftDevice 7.1.0 on an nRF51822.
Went with the dual-banked solution as that was what was available...
We are developing a blood glucose meter based on the nRF51.
To comply with Bluetooth Continua, do we just implement the Glucose Profile and Service (GLP and GLS)?
Do you...
Hi everyone,
I pass few days to try to fix my issue whiteout success.
I'm working on UART example provide by SDK 10 and tried to set up a communication from my computer...
Because of the power-saving support, I want to disable the UART before Call the sd_app_evt_wait().
I referred to two following sites to know the procedure of the case....
I'm working with a nrf51422/s110 dev kit on which I downloaded the Heart rate Monitoring sample project. On my PC, using a s130 dongle, I connect the device and wrote some...
Hello,
I would like to know about the possibility of programming the nrf51822 with a Keil ULINK-ME Debug Adapter (or, if necessary, Keil ULINKpro) instead of the recommended...
Our product has a legacy interface and for security reasons I want to allow users to disable or enable the BLE via this legacy interface.
My approach to this was to disable...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hello,
I am having much fun with nrf52. I'd like to implement SPI read (few bytes) per GPIOTE event over PPI, the source is the GPIO event and the destination task is a...
Hi,
I'm working with the nRF51822
I'm trying to enable the use of some timer callback on the ble_app_template.
I've succefully created and started all the timers, but i...
I have a modem connected to some pins on an nRF51822 on a custom board. Two pins on the modem are active low. One is a reset pin, the other a VCC control. I want these pins...
Can the nRF51822 DEC2 pin (LDO output) be used as a 1.8V supply for low current use (say, <50uA)? Similarly, how about the 1.9V output of the buck converter (AVdd)? The current...
I'm wondering if the latest version (8.x) of S110 supports BLE 4.1's "Connection Parameter Request Procedure". This procedure is described in the BLE 4.2 spec Volume 6, Part...
