Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
If I have a high-priority interrupt (or a series of them) that runs long enough to completely mask a radio notification, then all further radio notifications appear inverted...
I bought two EZAIRO 7150 SL hybrid board, (which contains a MOTHERBOARD & DAUGHTERBOARD). As part of the problems we have been having trying to establish a wireless connection...
Hi, I am developing a software that connects to nRF51822 over UART. I donot have the physical device currently so I downloaded its Soft device under the impression that it...
Hi,I update my MDK from 4.7 to 5.0,my old project can open ,but can't find the device list.I want to use 5.0 and 4.7 at the same time,and I have installed the SDK6.0 when...
Hi, when I compile my project the linker gives me the following error:
._build\nrf51422_xxac_s130.axf: Error: L6200E: Symbol GPIOTE_IRQHandler multiply defined (by app_gpiote_fast_detect...
I am working with nRF52832 and SD 132 and SDK 11 (nRF5_SDK_11.0.0-2.alpha_bc3f6a0).
One of my BLE services has a characteristic with an attribute larger than 22 bytes. It...
i was working with a nrf51822 module.after about 50 that i programmed the chip with my jlink programmer (some time i program it with stlink V2) it be damaged and not worked...
I am designing a BLE device. Want to make the PCB as small as possible. to download the code/debug etc I need the a connecter on the board which can connect to the nrf52 preview...
Please excuse my ignorance, My company is designing in the nRF52832 for our first product using both ANT and BLE. From looking at the documentation on thisisant.com there...
I've got a strange problem with updating my Magnet-Characteristic.
I use a service with 4 characteristics (Gyro, Acc, Mag and Temp Values) and update them on a timer base...
Hello,
Two issues want to ask, after tried the BLE_NUS example code.
From other posts, still does not exist clear solution (example, pictures) ?
Sure has an application...
Hello,
I am working with the uart module. While configuring the uart I encounter 2 issues.
First when in the uart_init function the pin for uart output is configured...
Hi,
I am using nrf51822(128k), SD 6.0, SDK 5.2.
I found that nrf uart v2.0 app will add a "0x0A" at the end of data that I want to send.
How can I remove this?
Thank...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
