after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
We are using the NRF board to act as node.
Samsung Galaxy S6 device is being used as the Router. We are trying to ping the node using ping6 command.
The issue is that the...
I have a working peripheral NUS application to pair/bond by entering passkey in the nrf master toolbox android application.
Now i want to replace the mobile witha nrf 51822...
nrf51822bluetooth low energycode 10
twiddle gravatar image
twiddle
1
asked May 9 '16
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just...
Hello Everyone,
I am designing the prototype using NRF51822 and i have choosen the DC DC power mode but the real problem is most of the time my radio will be sleeping so...
I have nRF52 Development Kit (PCA10040). I'm using Keil uVision.
I want to measure RSSI of some beacons and if the signal is strong then send MAC of this beacon over UART...
Hello Everyone
I'm trying to debug ble_app_beacon project, having the following error when trying to launch the debug session:
Error in final launch sequence Error executing...
Dear Sir:
I have a (BLE + 2.4GHz)Mouse project, But now I had some problmes. Please help deal,
Thank you so much Sir.
a). My program modification base on "nrfready_desktop_2_v3...
Hello all,
Just to note any versions that need saying, I am using
SD 110, V8
The 10.0 SDK, freshly unzipped
The dual bank BLE bootloader, unmodified
Arm...
I was looking at this PA/LNA example: here . I noticed something I'm not sure about, so I was hoping someone could shed some light on this.
In the diagram shown in the...
I've been working on a project, which requires data transmitted through ble to cell phone app. The user could acquire the data from the sensor when he sends a specific string...
Hi
We use the NRF51 in a mesh sensor network. We noticed in a trailer suited for cold chain transport (double metal walls with thermal isolation between) that the radio...
Hi,
I have problem with ble_nus_c.c in SDK v11...
Normal operation is:
Connecting to target 57E19A190FDF
Connected to target
[DB]: Starting discovery of service...
When I used the demo of ble_app_hrs_rscs_relay,I cannot write the bonding information to the flash.
I connect to the board by my phone.I cannot find the information about...
what I am basically trying to do is only allow a single bond and any new bonds disallowed until the user selects and option to allow a new bond and then and only then delete...
