Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hello,
I read the Errata document infocenter.nordicsemi.com/.../nRF52832_Engineering_B_Errata_v1.2.pdf , and in the section "3.10 [62] NFCT: Can draw current when not enabled...
Hello,
I'm designing a new design and planning to use WLCSP version of nRF52832.
I have few questions about this since all reference designs are made with QFN48 version...
Hi every one,
I use the nRF51822 to read temperature from sensor and send it through UART, i follow the SDK examples and just change connection interval to 0.5 sec and...
Hi I am trying to get my 128x32 oled device working with my nrf52 development kit board. Using PCA10040. Does anyone have or know of any example code that can get it up and...
Hello,
I am writing some data to flash, but when it runs to storage_clear, I get the return code---0x10. It seems clear failed. And I tried storage_update, and it failed...
Hi, I'm working on a project, I want nRF51822 can get notification when android phone got a call or email, just like ANCS work with iPhone.
I tried ble_app_alert_notification...
Hello,
Apologies as I'm very new to C and I may be missing something obvious. I have an actual ble Heart Rate device which I wish to connect to my pca10028 (nrf51422_xxAC...
I am try to porting nRF51822 Beacon v1.0.1 F/W for PCA20006 to PCA10001.
I could change GPIO port setting for button and LED.
Now normal beacon mode work fine and success...
We appear to have discovered today that if you do this sequence
sd_power_gpregret_clr(0xFF);
sd_power_gpregret_set(0xA0);
sd_power_gpregret_set(0x0B);
GPREGRET will...
I'm trying to understand the general structure of .h files.
nrf.h contains an #ifdef for NRF52.
I cannot find a #define NRF52 anywhere.
Any help appreciated.
Thanks...
We have our nrf52 working well with our iOS app - almost everything we need is in place. One last item (haha) we've been struggling with is to get the nrf52 to advertise our...
Hi,
I'm connecting to a proximity sensor, IQS263 over TWI interface and having some weird problems.
I'm using the same code I used to connect with the Invensense MPU...
Hi.
We are trying to get nrf52 to work with 1.8v spi master. We are using level sifter with it. However when we connect the nrf52 to level sifter to spi output, the whole...
i am working with nrf24l01 module with PA LNA circuitry for longer distance transmission.When i bought the module i received an antenna along with it which is an SMA antenna...
Hi,
I have read "Measuring Lithium battery voltage with nRF52" posted on 5-23-16 just as a point of reference.
System setup:
In my system the nRF52 is powered (VDD...