hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
when a particular line of my code is at line 54, the following compile error occurs:
error: #101: "assert_line_54" has already been declared in the current scope
line...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
hello,
On a device with nRF51822-CEAA packaged in a ISP130301, we have a problem with RSSI value measurement.
We use Master control panel and bluetooth usb key provide...
I have set up raspberry pi 3 as a border router and programmed the the nrf51422 using the iot_ipv6_coap_server_pca10028 and could successfully switch on and off led3 and led4...
nrf51822QfAC
S130 stack was working fine and ble_app was able run successfuly able to see the ble on the app;
Now after few days now facing issue in running the same code...
having issue with nrf51822
nrf51822 breakup board was running fine with S130 2.0 stack and ble_app_uart
Now facing issue such that when softdevice enabled is called the...
Hi,
I just switch to Embbeded Studio following the last tutorial ( here ).
I'm working on NRF51822 with SDK12 and TWI_sensor example (without SoftDevice). I followed...
I see from the release notes of s132 4.0.0-2.alpha that it adds:
Support for 20 links in total with freely selectable role (Central/Peripheral) for each link.
I want...
Hey,
I am trying to control an external LED using two nRF52832 boards. I am using "nRF5_SDK_13.0.0_04a0bfd\examples\ble_peripheral\experimental_ble_app_blinky" code for...
I'm trying to use the BLE sniffer in a quite busy BLE environment. Unfortunately, it always crashes after a few seconds.
I'm using:
ble-sniffer_win_1.0.1
nRF51 Dongle...
Hi,
i am using PCA10040 DK board,
working on ble_app_Uart example, i have created one timer(app_timer) here is the code:
printf("init\r\n");
ret_code_t err_code;...
Dear all,
My chip is nrf52832, and sdk version is SDK12.1.0_0d232a. And tried to use ble service and spi master function.
I create a timer to send spi command every...
hello all:
my mcu is nrf51822(QFAA), and use it to make a blue device ,i want to use mcu's reset pin to reset it, just use hardware. i add a key to connect the reset pin...
