Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hi,
currently trying to boot up mcuboot with nrf54l15 pm_static for both cpuapp and cpuapp_ns. Both files are included in the zip file.
I have already tried several configuartions...
Hello,
I need two signals with a phase shift to control my motor. For some reason, completely randomly, sometimes my GPIOTE event is not triggered and i get the inversion...
Hi All,
Based on nRF52832 SDK14.2 rtc example, I want to change it to retrigger RTC Compare0, let the LED1 also toggle every 3s, instead of keeping LED1 on. I tried to add...
Hi, guys, I have an IR receiver module with 3 pin (AX-1838HS) ?
How can I use it on my nrf52832 ? I have PCA10040 development board. I don't know how to connect them and...
I need to drive a stepper motor without software intervention, since strict timing is a must.In the following image you can see the required wave-forms - the motor requires...
The SD API (S132-6.0.0) documentation provides little beyond what one could guess from the function and type names. sd_mutex_acquire says "Attempt to acquire a mutex". nrf_mutex_t...
Hi i am doing a prosject to get notification on cell phone when i get mail in my postbox (postbox outside the house) I am using a nRF51 dongle, and want it to connect to cellphone...
Hi! I'm working on HID mouse example on SDK 13.0.0. I'm supposed to use this as a low power media button control. I've done a few modicifations on the code for power optimizations...
I know that few companies choose to use NRF528001 with a separate microcontroller like Fitbit.
I would like to know why would they do so instead of using an NRF52 chip that...
Hey,
I am using a nRF8001 with a STM32L051 as an application controller.
After resetting the nRF the RDYN pin goes low, as expected. Then I'm setting the REQN line LOW...
Hello all,
I have a Nordic Thingy 52 board, and I have download the Thingy 52 SDK, I can debug it successfully.
But after I debug it , or download it, the board runs with...
We have an application with FreeRTOS. If we do not initialize softdevice, the freertos interrupts tend to come in at a very very slow rate. I know that softdevice does clock...
nRFgo Studio displays a "Enable reset pin" option on the nRF52 DK but does not display this option on our custom hardware; we use a Segger J-Link for programming the custom...
Hello,
I would like to know the CALIBRATEOFFSET function in detail.
Could you disclose the part of source code on this CALIBRATEOFFSET function?
Best regards,
Kiyoshi...
