Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Hello,
I have implemented experimental DFU buttonless example with my application and able to do the firmware OTA via secure bootloader example using private and public...
Hi,
I'm experimenting with the nrf52840 preview board.
I have tried the example "ble_app_att_mtu_throughput" using the coded option to check the extended range and it...
hi, everyone!
I have a question for pstorage, when i use pstorage_store,it was failed, return error code :15 how to solve it. Below is my code
void custom_flash_init...
With good luck, I traced my connection timeout to the slave/peripheral using nrfSniffer. What is most unusual is the slave unexpectedly stops corresponding with the master...
Hello,
I am trying to implement DFU secure bootloader to do firmware update over the air for nrf51822.
I have followed the steps as per the blog
devzone.nordicsemi...
Hello,
I want to ask, did the nordic chip support I2C slave ? I want to make other controller (STM) as Master and Nordic chip as slave in I2C.
Is it possible? or Nordic...
Hello!
I am trying to increase the MTU size to get higher speeds. When I increase the MTU above 65 the application locks/software reset when doing transfer. Up to 65 it...
Hi, I'm facing an extremely strange problem with a product I'm developing.
I've been getting significant idle current measurements (around 7 mA), and I couldn't for the...
I recently attempted to upload a new image via OTA.
After emailing the zip file to my iPhone as an attachment and tapping on it,
then tapping on the share icon several choices...
Hello,
I need a voltage regulator to power a microphone at 1.3V from a 3V coin cell battery and I was looking for a regulator like the lm317 , but with this one the minimum...
IAR EW 8.11.1 does not link the nfc samples from sdk 13.1. There are different sizes for wchar_t:
Error[Lt009]: Inconsistent wchar_t size
nfc_t2t_lib.o(nfc_t2t_lib_iar...
Q1 I compile sdk13.0.0 generate nrf52840_xxaa.hex(app), nrf52840_xxaa_s140.hex(bootloader).
I used merge tool make a hex file, then burn the file into PCA10056 DK by nrfjprog...
Hi Nordic and fellow developers,
I have been working on upgrading the nRF51822 QFAA s110 and upgrading the softdevice to work as s130 for its (simultaneous Central/Peripheral...
