Hello,
I am trying to count pulses on nRF52840 DK's pin for measuring water flow with hall effect sensor. I tried to implement PPI + GPIOTE + TIMER in counter mode, but...
Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hello,
We are currently evaluating a very low power application using the nRF5340+7002. Our hardware design includes a complex power supply configuration, and we need to...
Retrieving Custom Firmware Version from nRF52 BLE Controller to nRF9160 Host
Product: nRF Connect SDK v2.6.0 Hardware: nRF9160 (Host) connected via UART to nRF52832 (Controller...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
I am having very limited knowledge in flashing devices, infact this is the first time I was doing it, pls conider
Step 1: I bough PCA10040 and installed nRFGo software in...
I have found multiple PDFs indicating the lay-out on the nRF52-DK. However, none of them tell me anything about the size of the kit. Does anyone have a PCB lay-out with at...
Using the latest SDK and following example multiprotocol/ble_app_gzl.
I try to add a vendor specific UUID and get error 4. Which means, not enough room in some table? Whose...
Hi,
I hope this is the appropriate forum for this question. I've also asked this on the developer forum on thisisant.com, but received no answer there.
We are using...
Hi all,
I have a custom board with 3 LED's and one button. I have created a custom_board.h file:
#define LEDS_NUMBER 3
#define LED_START 22
#define LED_1 22
#define...
I wanna build project nRF51822 using ADXL345 for accelerometer sensor that program using eclipse or keil. can you teach me how to build using nRF51822 SDK version 6 or higher...
Hi,
I'd just start developping with the nRF52832 and I would like to communicate with a sensor using the I2C protocol. Has I am a stranger with the nordic uC, I would like...
Hi guys, me again.
I was very confused with my current process on developing with nrf chip now... so I would like to post my develop step and some problems I had so maybe...
I am using ATT MTU throughput example and I noticed that using CLI (calling cli_start) causes the main while(1) loop forever. In other words, wait_for_event does not block...
I just received the Nordic nRF52-DK, and am unable to do anything with it as my laptop does not recognize when it is connected. I do not have the original cable as I did not...
Hi!
I have AD5611 DAC connected to nRF51822 by SPI.
In DAC datasheet we need to send data by MSB first order.
Data packet is 16 bit length.
I feel variable uint16_t...
Hello,
I use the pca10040 and the problem is in 14.0 eaxmple ,when I push the button switch the protocol mode like : ble->gzll->ble and then I find the example loop into...
Hello,
based on the saadc example of SDK 11 I am trying to change the code to use the SAADC's local timer to sample the input given number of times (10 times for the below...
Hi,
well I struggle with another problem right now.
In case of some errors, I use 'sd_nvic_SystemReset' to reset the system.
But the WDT is used in the application. Thus...
