I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi All,, please confirm me this .. please confirm i-beacon Rx + ble peripheral is possible ... Also please suggest me a development kit for the same which can be easily solder...
Hello,
I would like to move the SDK12.2 template example project out of SDK12.2 installation directory. How can I do that using uVision5?
I tried to change all the reference...
Hi
I don't understand how to correctly flash all three parts so that the app runs on boot.
At the moment if I flash them all the nrf51 (51822) boots to the dfu bootloader...
I can see in the latest SDK 12.2 that signing of the dfu firmware files is possible.
Am I right in thinking that this signing verifies the source of the firmware files...
Hi, I have nrf51822QFAA series. I am using S110 for softdevice which takes 96KB. My current program size is Code=31908 RO-data=512 RW-data=312 ZI-data=8360. I want to know...
Hi.
I am using the new SDK 13.0.0 and nrf52 chip. I am trying to set a whitelist with
the peripheral_template example code.
I think the whitelist is already enabled in...
I have made an ADC driver that (should) scan 5 inputs into a sample buffer using EasyDMA. On the END event the 5 samples are transferred to 5 ring buffers read by the client...
I've tried to upgrade the firmware using the DFU feature of the android nrf-toolbox app, but it returns the "REading file failed" error.
this happens only with my phone...
Hello,
I am using sdk 11 and I am refering to code ble_app_uart. I am using nrf51 and I want to add passkey to this code. So do this I added
// Add static pin:
uint8_t...
Hi,
I measured the throughput using the ATT_MTU Throughput Example.
I referred to Testing in the following URL.
infocenter.nordicsemi.com/.../ble_sdk_app_att_mtu.html...
Hi,
Is Ibeacons are normal advertising packets ?
Will all the BLE Central which scan receive this ibeacons ?
Can I use NRF51822 as a device which receive the ibeacon...
as far as I am concerned, when I use PPI or SHORTS without interrupts, I DON'T need to clear the corresponding event registers, and task will be triggered once the event is...
Hi, Noric
When I use Master Control panel to connect my nRF52 for DFU, it shows:
Then when I press "Start", it shows:
Plz help me.
Which example will be flashed...
Hi everyone. I am working on a project while doing my undergrad in EE and am confused on a few things.
I am using Raspberry Pi 3s with the NRF24L01 (NRFL) chip and code...
Hello!) Have some problem with custom pcb, created for nrf52832. After mounting all components a connected pcb to nrf52dk through P20 port. Chip was correctly detected in...
