Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Looking at the documentation here (for SDK 11, s130)...
infocenter.nordicsemi.com/index.jsp
I see two conflicting statements
These APIs require that the...
The examples of whitelisting that I am looking at (ble_app_proximity, ble_app_hrs_c) both create their whitelists just before a scan. I am wondering if this is actually the...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
Hi,
I want to use more than 8 devices with gazelle protocol, so is there any way to expand the pipe number or change the pipe addresses in runtime ? Host device will know...
Hello, I have a problem NRF905. Sending distance is 0-30 cm maximum.
I want to ask if the defective product or it may be due code?
TX RX uses the base code of the library...
Hi Team,
In current application, each BLE node (nRF51x22) need to switch between Broadcaster and observer roles . Beacon kind of behavior is required i.e. no connection...
Hi All,
Please, I have some questions about the use of iPhone wireless shutter release button:
Q1: Is it possible to connect to an iPhone wireless shutter release button...
Open the nRFgo Studio and connect PCA10028 (NRF 51DK Board) then Erase all data
Open the uVision V5.18a
Open the DTM project file of the example in the following...
Refer to the NRF 51DK Spec page, It can be support Bluetooth 4.2 spec.
In the Bluetooth 4.2 spec, The device can support the maximum PDU size of 255 bytes
Where can I...
Hi Everyone,
I face a problem regarding uploading Application Hex file, I use nRF Toolbox v 1.15.0 mobile app to upload the firmware, Bootloader is successfully uploaded...
Helo, i'm working on firmware for a device, which should be able to scan for other devices, advertise data and be connectable. Scanning and advertising works. Problems come...
Hi All,
Am using NRF52 ,S132 soft device , I am trying to send two packet of twenty byte every 5s . in a timer interrupt handler I call ble_nus_string_send twice continuosly...
I have following set up for current measurement.
NRF52 DK PCA10040 v0.9.0
nRF5 SDK v11.0.0 : Power Profiling Application
S132 SoftDevice v2.0.0
nFR Master Control...
hi
does my nrf51422 v2 have uart over ble?
its version 2 and its supported sdk is 6 and it does not have ble_nus.c
does my nr51422 v2 support uart over ble?
